Legacy branch migration

.gitignore

@@ -1,3 +1,23 @@
+# Ignore list for Atmel studio files
+# Hidden folder
+.vs/
+
+#Build Directories
+Debug/
+Release/
+
+#Build Results
+*.o
+*.d
+*.eep
+*.elf
+*.hex
+*.map
+*.srec
+
+#User Specific Files
+*.atsuo
+
 # Ignore list for Altium temp files
 History/
 __Previews/
@@ -9,3 +29,4 @@ Project Logs for*
 # Ignore list for Generated output files
 *.step
 OUTPUTS/
+

firmware/devices/analog.c

@@ -0,0 +1,120 @@
+/**** Includes ****/
+#include "hal/udccd_hal.h"
+#include "analog.h"
+
+/**** Private variables ****/
+static const uint8_t ICOIL_MUL = 215;
+static const uint8_t ICOIL_DIV = 22;
+static const int16_t ICOIL_OFF = 0;
+static const uint8_t ICOIL_CNT = 1;
+
+static const uint8_t UCOIL_MUL = 20;
+static const uint8_t UCOIL_DIV = 1;
+static const int16_t UCOIL_OFF = 0;
+static const uint8_t UCOIL_CNT = 1;
+
+static const uint8_t UBAT_MUL = 20;
+static const uint8_t UBAT_DIV = 1;
+static const int16_t UBAT_OFF = 0;
+static const uint8_t UBAT_CNT = 1;
+
+static const uint8_t IBAT_MUL = 235;
+static const uint8_t IBAT_DIV = 6;
+static const int16_t IBAT_OFF = 0;
+static const uint8_t IBAT_CNT = 1;
+
+static const uint8_t POT_MUL = 215;
+static const uint8_t POT_DIV = 44;
+static const int16_t POT_OFF = 0;
+static const uint8_t POT_CNT = 1;
+
+static const uint8_t MODE_MUL = 215;
+static const uint8_t MODE_DIV = 44;
+static const int16_t MODE_OFF = 0;
+static const uint8_t MODE_CNT = 1;
+
+
+/**** Private function declarations ****/
+static uint16_t ConvertSIntShort(int32_t in);
+static uint16_t ConvertUintShort(uint32_t in);
+static uint16_t read_ch(adcCh_t ch, uint16_t gnd_raw, uint8_t mul, uint8_t div, int16_t offset, uint8_t samples);
+
+/**** Public function definitions ****/
+void Analog_UpdateAll(analog_t* meas)
+{
+	uint16_t gnd_lvl = HAL_ADC_Read(ADC_GND);
+	
+	meas->hb_currnet     = read_ch(ADC_ICOIL, 0, ICOIL_MUL, ICOIL_DIV, ICOIL_OFF, ICOIL_CNT ); //mA
+	meas->hb_voltage     = read_ch(ADC_UCOIL, 0, UCOIL_MUL, UCOIL_DIV, UCOIL_OFF, UCOIL_CNT ); //mV
+	meas->supply_current = read_ch(ADC_IBAT , 0, IBAT_MUL , IBAT_DIV , IBAT_OFF , IBAT_CNT  ); //mA
+	meas->supply_voltage = read_ch(ADC_UBAT , 0, UBAT_MUL , UBAT_DIV , UBAT_OFF , UBAT_CNT  ); //mV
+	meas->pot_voltage    = read_ch(ADC_POT  , 0, POT_MUL  , POT_DIV  , POT_OFF  , POT_CNT   ); //mV
+	meas->mode_voltage   = read_ch(ADC_MODE , 0, MODE_MUL , MODE_DIV , MODE_OFF , MODE_CNT  ); //mV
+	
+	// Calculate derived measurements
+	// Halfbridge output power
+	uint32_t temp = (uint32_t)meas->hb_currnet * (uint32_t)meas->hb_voltage;
+	temp /= 1000;
+	meas->hb_power = ConvertUintShort(temp);
+	
+	// Halfbridge output resistance
+	if(meas->hb_currnet == 0) meas->hb_resistance = 0xFFFF;
+	else if(meas->hb_voltage == 0) meas->hb_resistance = 0;
+	else
+	{
+		temp = (uint32_t)meas->hb_voltage * 1000;
+		temp /= (uint32_t)meas->hb_currnet;
+		meas->hb_resistance = ConvertUintShort(temp);
+	}
+	
+	// Supply power
+	temp = (uint32_t)meas->supply_current * (uint32_t)meas->supply_voltage;
+	temp /= 1000;
+	meas->supply_power = ConvertUintShort(temp);
+}
+
+static uint16_t read_ch(adcCh_t ch, uint16_t gnd_raw, uint8_t mul, uint8_t div, int16_t offset, uint8_t samples)
+{
+	//Sanity check
+	if(div==0) return 0xFFFF;
+	
+	// Do at least one sample
+	if(samples<1) samples = 1;
+	
+	// Read ADC value
+	int32_t raw = 0;
+	for(uint8_t i=0; i<samples; i++)
+	{
+		raw += (int32_t)HAL_ADC_Read(ch);
+	}
+	
+	// Do average
+	if(samples != 1)
+	{
+		raw /= samples;
+	};
+	
+	// Remove GND level
+	if(gnd_raw)	raw = raw - (int32_t)gnd_raw;
+	
+	// Convert to target units	
+	raw = raw * mul;
+	if(div!=1) raw /= div;
+	raw += offset;
+	
+	return ConvertSIntShort(raw);
+}
+
+static uint16_t ConvertSIntShort(int32_t in)
+{
+	if(in <= 0) return 0;
+	else if(in >= 0x0000FFFF) return 0xFFFF;
+	else return (uint16_t)in;
+}
+
+static uint16_t ConvertUintShort(uint32_t in)
+{
+	if(in == 0) return 0;
+	else if(in >= 0x0000FFFF) return 0xFFFF;
+	else return (uint16_t)in;
+}

firmware/devices/analog.h

@@ -0,0 +1,23 @@
+#ifndef ANALOG_H_
+#define ANALOG_H_
+
+/**** Includes ****/
+#include <stdint.h>
+
+/**** Public definitions ****/
+typedef struct {
+	uint16_t hb_currnet;
+	uint16_t hb_voltage;
+	uint16_t hb_power;
+	uint16_t hb_resistance;
+	uint16_t supply_current;
+	uint16_t supply_voltage;
+	uint16_t supply_power;
+	uint16_t pot_voltage;
+	uint16_t mode_voltage;
+} analog_t;
+
+/**** Public function declarations ****/
+void Analog_UpdateAll(analog_t* meas);
+
+#endif /* ANALOG_H_ */

firmware/devices/common/level.h

@@ -0,0 +1,11 @@
+#ifndef LEVEL_T_H_
+#define LEVEL_T_H_
+
+/**** Public definitions ****/
+typedef enum {
+	HIZ = -1,
+	LOW = 0,
+	HIGH = 1
+} level_t;
+
+#endif /* LEVEL_T_H_ */

firmware/devices/config.c

@@ -0,0 +1,24 @@
+/**** Includes ****/
+#include "hal/udccd_hal.h"
+#include "config.h"
+
+/**** Public function definitions ****/
+void Init_HW(void)
+{
+	hwConfig_t hwCfg;
+	hwCfg.adc_clk_prescaler = ADC_DIV2;
+	hwCfg.adc_auto_wake = 1;
+	// 64kHz PWM
+	hwCfg.pwm_timer_prescaler = TIM_DIV1;
+	hwCfg.pwm_timer_top = 0x01FF;
+	// 1.9Hz..62.5kHz Speed input
+	hwCfg.freq_timer_prescaler = TIM_DIV64;
+	// 1kHz systick
+	hwCfg.systick_timer_top = 125;
+	hwCfg.systick_timer_prescaler = TIM_DIV64;
+	// No extra features
+	hwCfg.uart_prescaler = 0;
+	hwCfg.disable_unused = 0;
+	hwCfg.en_watchdog = 0;
+	HAL_Init_Min(&hwCfg);
+}

firmware/devices/config.h

@@ -0,0 +1,10 @@
+#ifndef CONFIG_H_
+#define CONFIG_H_
+
+/**** Includes ****/
+#include <stdint.h>
+
+/**** Public function declarations ****/
+void Init_HW(void);
+
+#endif /* CONFIG_H_ */

firmware/devices/filter_iir_lpf.c

@@ -0,0 +1,21 @@
+/**** Includes ****/
+#include "filter_iir_lpf.h"
+
+/**** Private variables ****/
+
+/**** Public function definitions ****/
+uint16_t LPF_Update(uint16_t new, uint16_t last, uint8_t strength)
+{
+	if(strength==0) return new;
+	else if(strength==255) return last;
+	else
+	{
+		uint32_t temp = (uint32_t)last * strength;
+		temp += new * (255-strength);
+		temp /= 255;
+		
+		//Limit to 16bits
+		if(temp > 0x0000FFFF) return 0xFFFF;
+		else return (uint16_t) temp;
+	}
+}

firmware/devices/filter_iir_lpf.h

@@ -0,0 +1,10 @@
+#ifndef FILTER_IIR_LPF_H_
+#define FILTER_IIR_LPF_H_
+
+/**** Includes ****/
+#include <stdint.h>
+
+/**** Public function declarations ****/
+uint16_t LPF_Update(uint16_t new, uint16_t last, uint8_t strength);
+
+#endif /* FILTER_IIR_LPF_H_ */

firmware/devices/hal/udccd_hal.h

@@ -0,0 +1,102 @@
+#ifndef UDCCD_R8_BSP_H_
+#define UDCCD_R8_BSP_H_
+
+/**** Includes ****/
+#include <stdint.h>
+#include "../common/level.h"
+
+/**** Public definitions ****/
+//ADC definitions
+typedef enum {
+	ADC_ICOIL = 0x00,
+	ADC_UCOIL = 0x01,
+	ADC_UBAT = 0x02,
+	ADC_IBAT = 0x03,	
+	ADC_POT = 0x04,
+	ADC_MODE = 0x05,
+	ADC_TEMP = 0x08,
+	ADC_INTREF = 0x0E,
+	ADC_GND = 0x0F
+} adcCh_t;
+
+typedef enum {
+	ADC_DIV2 = 0x01,
+	ADC_DIV4 = 0x02,
+	ADC_DIV8 = 0x03,
+	ADC_DIV16 = 0x04,
+	ADC_DIV32 = 0x05,
+	ADC_DIV64 = 0x06,
+	ADC_DIV128 = 0x07
+} adcDiv_t;
+
+//Timer definitions
+typedef enum {
+	TIM_DIV1 = 0x01,
+	TIM_DIV8 = 0x02,
+	TIM_DIV64 = 0x03,
+	TIM_DIV256 = 0x04,
+	TIM_DIV1024 = 0x05
+} timerDiv_t;
+
+typedef enum {
+	PWM_COIL = 'A',
+	PWM_LED = 'B'
+} pwmCh_t;
+
+typedef enum {
+	SPEED_1 = 3,
+	SPEED_0 = 4
+} speedCh_t;
+
+typedef struct {
+	adcDiv_t adc_clk_prescaler;
+	uint8_t adc_auto_wake;
+	timerDiv_t pwm_timer_prescaler;
+	uint16_t pwm_timer_top;
+	timerDiv_t freq_timer_prescaler;
+	uint16_t uart_prescaler;
+	uint8_t systick_timer_top;
+	timerDiv_t systick_timer_prescaler;
+	uint8_t disable_unused;
+	uint8_t en_watchdog;
+} hwConfig_t;
+
+/**** Public function declarations ****/
+void HAL_Init_Min(hwConfig_t* hwCfg);
+void HAL_Init_Extra(hwConfig_t* hwCfg);
+
+level_t HAL_ReadLvl_Handbrake(void);
+level_t HAL_ReadLvl_Brake(void);
+level_t HAL_ReadLvl_Dimm(void);
+level_t HAL_ReadLvl_BtnUp(void);
+level_t HAL_ReadLvl_BtnDown(void);
+level_t HAL_ReadLvl_BtnMode(void);
+level_t HAL_ReadLvl_HandbrakePull(void);
+level_t HAL_ReadLvl_CoilLow(void);
+level_t HAL_ReadLvl_CoilHigh(void);
+level_t HAL_ReadLvl_LedsPwm(void);
+level_t HAL_ReadLvl_Speed0(void);
+level_t HAL_ReadLvl_Speed1(void);
+level_t HAL_ReadLvl_SpeedPull(void);
+
+void HAL_SetPull_Handbrake(level_t lvl);
+void HAL_SetPull_Speed(level_t lvl);
+
+void HAL_ADC_Wake(void);
+void HAL_ADC_Sleep(void);
+uint16_t HAL_ADC_Read(adcCh_t ch);
+
+void HAL_Coil_SetLowSide(uint8_t on);
+void HAL_Coil_SetPWM(uint8_t percent);
+void HAL_Coil_SetPWM16b(uint16_t value);
+
+void HAL_LEDS_Set(uint8_t image);
+uint8_t HAL_LEDS_Get(void);
+void HAL_LEDS_SetPWM(uint8_t percent);
+
+void HAL_PWM_Wake(void);
+void HAL_PWM_Sleep(void);
+void HAL_PWM_SetDuty16b(pwmCh_t ch, uint16_t value);
+void HAL_PWM_SetDuty100(pwmCh_t ch, uint8_t percent);
+
+#endif /* UDCCD_R8_BSP_H_ */

firmware/devices/hal/udccd_r7_hal.c

@@ -0,0 +1,463 @@
+/**** Includes ****/
+#include <avr/io.h>
+#include "udccd_hal.h"
+
+/**** Private variables ****/
+static uint8_t tim0_prescaler = 0x00;
+static uint8_t tim1_prescaler = 0x00;
+static uint8_t tim3_prescaler = 0x00;
+static uint8_t tim4_prescaler = 0x00;
+
+/**** Private function declarations ****/
+static void PWM_SetOCx(pwmCh_t ch, uint16_t value);
+
+/**** Public function definitions ****/
+void HAL_Init_Min(hwConfig_t* hwCfg)
+{
+	// PIN Configuration
+	//DCCD Enable and PWM
+	PORTB &= ~0x03; //Set low
+	DDRB |= 0x03;  //Set as outputs
+	
+	//LED PWM
+	PORTB &= ~0x04;  //Set low
+	DDRB |= 0x04;   //Set as output
+	
+	//UART TX
+	PORTB |= 0x18;  //Set high / pull-up on
+	DDRB |= 0x08;  //Set as output
+	DDRB &= ~0x10;  //Set as input
+	
+	//Handbrake pull-up
+	PORTB |= 0x20;  //Set high
+	DDRB |= 0x20;   //Set as output
+	
+	//Handbrake and Brake inputs
+	PORTB |= 0xC0;  //Pull-up on
+	DDRB &= ~0xC0;  //Set as input
+	
+	// ADC inputs
+	PORTC &= ~0x3F; //Pull-up off
+	DDRC &= ~0x3F;  //Set as inputs
+	
+	// Reset
+	PORTC |= 0x40; //Pull-up on
+	DDRC &= ~0x40;  //Set as input
+	
+	// LED control
+	PORTD &= ~0x3F;  //Set low
+	DDRD |= 0x3F;   //Set as outputs
+	
+	// Speed pull
+	PORTD &= ~0x40;  //Set low
+	DDRD |= 0x40;   //Set as outputs
+	
+	// Dim input
+	PORTD |= 0x80;  //Set pull-up on
+	DDRD &= ~0x80;   //Set as input
+	
+	// Speed inputs
+	PORTE &= ~0x05;  //Set pull-down
+	DDRE |= 0x05;   //Set as output
+	
+	// Up/Down inputs
+	PORTE |= 0x0A;  //Set pull-up on
+	DDRE &= ~0x0A;   //Set as input
+	
+	
+	//ADC configuration
+	PRR0 &= ~0x01; //Enable ADC power
+	DIDR0 |= 0x1F; //Disable digital inputs, ADC0-ADC4
+		
+	ADMUX = 0x40;  //Set AVCC reference, Right adjust
+	ADCSRA = 0x00; //ADC Disabled, Single conversion, no IT
+	ADCSRA |= (uint8_t)hwCfg->adc_clk_prescaler;
+	ADCSRB = 0x00; //no trigger input
+	
+	if(hwCfg->adc_auto_wake) ADCSRA |= 0x80;  //Enable ADC
+	else PRR0 |= 0x01;
+
+
+	//DCCD and LED PWM configuration
+	PRR0 &= ~0x80;  //Enable Timer1 power
+	TCCR1A = 0xF2; //Connect OC1A and OC1B, normal logic
+	TCCR1B = 0x18; //PWM, Phase & Frequency Correct ICR1 top, no clock, WGM:0xE
+	TCCR1C = 0x00;
+	TCNT1 = 0x0000;
+	OCR1A = 0x0000;
+	OCR1B = 0x0000;
+	ICR1 = (hwCfg->pwm_timer_top);
+	TIMSK1 = 0x00;  //No interrupts
+	TIFR1 = 0x00;	//Clear all flags
+	
+	tim1_prescaler = (uint8_t)hwCfg->pwm_timer_prescaler;
+	TCCR1B |= tim1_prescaler;  //Enable timer
+}
+
+void HAL_Init_Extra(hwConfig_t* hwCfg)
+{
+	//Speed 1 input timer configuration
+	PRR1 &= ~0x01;  //Enable Timer3 power
+	TCCR3A = 0x00;  //OCx disconnected, WGM:0x0
+	TCCR3B = 0x80;  //ICP Noise filter, Falling edge, no clock
+	TCCR3C = 0x00;
+	TCNT3 = 0x0000;
+	OCR3A = 0x0000;
+	OCR3B = 0x0000;
+	ICR3 = 0x0000;
+	TIMSK3 = 0x00;
+	//TIMSK3 |= 0x21; //ICP and OVF interrupts
+	TIFR3 = 0x00;	//Clear all flags
+	
+	tim3_prescaler = (uint8_t)hwCfg->freq_timer_prescaler;
+	TCCR3B |=  tim3_prescaler; //Enable timer
+	
+	
+	//Speed 0 input timer configuration
+	PRR1 &= ~0x08;  //Enable Timer4 power
+	TCCR4A = 0x00;  //OCx disconnected, WGM:0x0
+	TCCR4B = 0x80;  //ICP Noise filter, Falling edge, no clock
+	TCCR4C = 0x00;
+	TCNT4 = 0x0000;
+	OCR4A = 0x0000;
+	OCR4B = 0x0000;
+	ICR4 = 0x0000;
+	TIMSK4 = 0x00;
+	//TIMSK4 |= 0x21;	//ICP and OVF interrupts
+	TIFR4 = 0x00;	//Clear all flags
+	
+	tim4_prescaler = (uint8_t)hwCfg->freq_timer_prescaler;
+	TCCR4B |= tim4_prescaler;  //Enable timer
+	
+	
+	//UART1 configuration
+	PRR0 &= 0x10;   //Enable UART1 power
+	UCSR1A = 0x00;  //Clear flags, Single UART speed, Single processor mode
+	UCSR1B = 0x18;  //Enable RX/TX hardware, 8bit char
+	//UCSR1B |= 0xC0; //Enable RX/TX interrupt,
+	UCSR1C = 0x06; ; //async, No parity, 1 stop bit, 8bit char,
+	UBRR1 = hwCfg->uart_prescaler; //UART baud rate select
+	
+	
+	//"Systick" timer configuration
+	PRR0 &= ~0x20; //Enable Timer0 power
+	TCCR0A = 0x02 ;//OC0x not connected, WGM 0x01-CTC OC0A TOP
+	TCCR0B = 0x00; //WGM 0x01-CTC, No clock
+	TIMSK0 = 0x00;
+	//TIMSK0 |= 0x01; //OVF interrupt enabled
+	TCNT0 = 0x00;
+	OCR0A = hwCfg->systick_timer_top;
+	OCR0B= 0x00;
+	TIFR0 = 0x00; //Reset all flags
+	
+	tim0_prescaler = (uint8_t)hwCfg->systick_timer_prescaler;
+	TCCR0B |= tim0_prescaler;
+	
+	
+	//Disabled not used power configuration
+	if(hwCfg->disable_unused)
+	{
+		//Disable power to not used peripherals
+		PRR0 |= 0xC6; //Disable TWI0, TIM2, SPI0, UART0
+		PRR1 |= 0x34; //Disable TWI1, PRTC, SPI1
+	}
+	
+	//Watchdog configuration
+	if(hwCfg->en_watchdog)
+	{
+		//watchdog timer setup
+		WDTCSR |= 0x10; //Change enable
+		WDTCSR |= 0x0D; //System reset mode, 0.5s period.
+		//use special instruction to reset watchdog timer
+	};
+}
+
+
+// Handbrake input
+level_t HAL_ReadLvl_Handbrake(void)
+{
+	if(PINB & 0x40) return HIGH;
+	else return LOW;
+}
+
+// Brakes input
+level_t HAL_ReadLvl_Brake(void)
+{
+	if(PINB & 0x80) return HIGH;
+	else return LOW;
+}
+
+// Dimm input
+level_t HAL_ReadLvl_Dimm(void)
+{
+	if(PIND & 0x80) return HIGH;
+	else return LOW;
+}
+
+// UP button
+level_t HAL_ReadLvl_BtnUp(void)
+{
+	if(PINE & 0x08) return HIGH;
+	else return LOW;
+}
+
+// Down button
+level_t HAL_ReadLvl_BtnDown(void)
+{
+	if(PINE & 0x02) return HIGH;
+	else return LOW;
+}
+
+// Mode button
+level_t HAL_ReadLvl_BtnMode(void)
+{
+	if(PINC & 0x20) return HIGH;
+	else return LOW;
+}
+
+// Handbrake pull
+level_t HAL_ReadLvl_HandbrakePull(void)
+{
+	if(PINB & 0x20) return HIGH;
+	else return LOW;
+}
+
+// Coil driver control low
+level_t HAL_ReadLvl_CoilLow(void)
+{
+	if(PINB & 0x01) return HIGH;
+	else return LOW;
+}
+
+// Coil driver control high
+level_t HAL_ReadLvl_CoilHigh(void)
+{
+	if(PINB & 0x02) return HIGH;
+	else return LOW;
+}
+
+// LED PWM control
+level_t HAL_ReadLvl_LedsPwm(void)
+{
+	if(PINB & 0x04) return HIGH;
+	else return LOW;
+}
+
+// Speed 0 input pin
+level_t HAL_ReadLvl_Speed0(void)
+{
+	if(PINE & 0x04) return HIGH;
+	else return LOW;
+}
+
+// Speed 1 input pin
+level_t HAL_ReadLvl_Speed1(void)
+{
+	if(PINE & 0x01) return HIGH;
+	else return LOW;
+}
+
+// Speed common pull pin
+level_t HAL_ReadLvl_SpeedPull(void)
+{
+	if(PIND & 0x40) return HIGH;
+	else return LOW;
+}
+
+
+// Set handbrake pull-up
+void HAL_SetPull_Handbrake(level_t lvl)
+{
+	switch(lvl)
+	{
+		case HIGH:
+		PORTB |= 0x20;  //Set high
+		DDRB |= 0x20;   //Set as output
+		break;
+		
+		case LOW:
+		PORTB &= ~0x20;  //Set low
+		DDRB |= 0x20;   //Set as output
+		
+		default:
+		DDRB &= ~0x20;   //Set as input
+		PORTB |= 0x20;  //Set high
+		break;
+	}
+}
+
+// Set speed inputs common pull
+void HAL_SetPull_Speed(level_t lvl)
+{
+	switch(lvl)
+	{
+		case HIGH:
+		PORTD |= 0x40;  //Set high
+		break;
+		
+		default:
+		PORTD &= ~0x40;  //Set low
+		break;
+	}
+}
+
+
+// ADC Wake
+void HAL_ADC_Wake(void)
+{
+	//Enable ADC power
+	PRR0 &= ~0x01;
+	//Enable ADC
+	ADCSRA |= 0x80;
+}
+
+// ADC Sleep
+void HAL_ADC_Sleep(void)
+{
+	//wait to finish
+	while(ADCSRA&0x40);
+	//Disable ADC
+	ADCSRA &= ~0x80;
+	//Disable ADC power
+	PRR0 |= 0x01;
+}
+
+// ADC Read
+uint16_t HAL_ADC_Read(adcCh_t ch)
+{
+	//check if ADC is enabled
+	if(!(ADCSRA&0x80)) return 0xFFFF;
+	
+	uint8_t mux = (uint8_t)ch;
+	//Safe guard mux
+	if(mux > 15) return 0xFFFF;
+	// Not available channels
+	if((mux > 8) && (mux<14)) return 0xFFFF;
+	
+	ADMUX &= ~0x0F;
+	ADMUX |= mux;
+	ADCSRA |= 0x40;
+	while(ADCSRA&0x40); //wait to finish
+	return ADC;
+}
+
+
+// Coil Driver Low Side control
+void HAL_Coil_SetLowSide(uint8_t on)
+{
+	if(on) PORTB |= 0x01;
+	else PORTB &= ~0x01;
+}
+
+void HAL_Coil_SetPWM(uint8_t percent)
+{
+	HAL_PWM_SetDuty100(PWM_COIL, percent);
+}
+
+void HAL_Coil_SetPWM16b(uint16_t value)
+{
+	HAL_PWM_SetDuty16b(PWM_COIL, value);
+}
+
+
+// LED Display
+void HAL_LEDS_Set(uint8_t image)
+{
+	//Read current PORTD pin6, pin7
+	uint8_t keep = PORTD & 0xC0;
+	
+	//Safe guard display
+	image &= 0x3F;
+	
+	//Calculate new PORTD
+	keep |= image;
+	
+	//Set PORTD
+	PORTD = keep;
+}
+
+uint8_t HAL_LEDS_Get(void)
+{
+	return (PIND & 0x3F);
+}
+
+void HAL_LEDS_SetPWM(uint8_t percent)
+{
+	HAL_PWM_SetDuty100(PWM_LED, percent);
+}
+
+
+// PWM Direct functions
+void HAL_PWM_Wake(void)
+{
+	//Enable Timer1 power
+	PRR0 &= ~0x80;
+	//Prepare Timer1 settings
+	TCNT1 = 0x0000;
+	OCR1A = 0x0000;
+	OCR1B = 0x0000;
+	//Enable clock
+	TCCR1B |= tim1_prescaler;  //Enable timer
+}
+
+void HAL_PWM_Sleep(void)
+{
+	// Turn off outputs
+	OCR1A = 0x0000;
+	OCR1B = 0x0000;
+	// Force timer to bottom
+	TCNT1 = (ICR1-1);
+	// Wait for outputs to be off
+	while((PINB&0x06)!=0x00) continue;
+	// Disable clock
+	TCCR1B &= ~0x07;
+	// Disable Timer1 power
+	PRR0 |= 0x80;
+}
+
+void HAL_PWM_SetDuty16b(pwmCh_t ch, uint16_t value)
+{
+	value = 0xFFFF - value;
+	
+	uint32_t top = (uint32_t)ICR1;
+	uint32_t temp = (uint32_t)value * top;
+	temp = temp/0x0000FFFF;
+	//Limit temp
+	if(temp>0x0000FFFF) temp = 0x0000FFFF;
+	uint16_t ocrx = (uint16_t) temp;
+	
+	PWM_SetOCx(ch, ocrx);
+}
+
+void HAL_PWM_SetDuty100(pwmCh_t ch, uint8_t percent)
+{
+	if(percent > 100) percent = 100;
+	percent = 100 - percent;
+	
+	uint32_t top = (uint32_t)ICR1;
+	uint32_t temp = (uint32_t)percent * top;
+	temp = temp/100;
+	//Limit temp
+	if(temp>0x0000FFFF) temp = 0x0000FFFF;
+	uint16_t ocrx = (uint16_t) temp;
+	
+	PWM_SetOCx(ch, ocrx);
+}
+
+/**** Private function definitions ****/
+static void PWM_SetOCx(pwmCh_t ch, uint16_t value)
+{
+	switch(ch)
+	{
+		case PWM_COIL:
+		OCR1A = value;
+		return;
+		
+		case PWM_LED:
+		OCR1B = value;
+		return;
+		
+		default:
+		return;
+	}
+}

firmware/devices/halfbridge.c

@@ -0,0 +1,127 @@
+/**** Includes ****/
+#include "hal/udccd_hal.h"
+#include "halfbridge.h"
+
+/**** Private variables ****/
+static const uint16_t min_dc = 3277;  //5%
+static const uint16_t max_dc = 62258; //95%
+
+static uint16_t target = 0;
+static uint8_t low_side_on = 1;
+
+static uint16_t active_dc = 0;
+
+static uint8_t is_en = 0;
+
+/**** Private function declarations ****/
+static uint16_t CalculateDuty16b(uint16_t target, uint16_t supply);
+
+/**** Public function definitions ****/
+void HB_SetTarget(uint16_t voltage)
+{
+	target = voltage;
+}
+
+void HB_SetLowSide(uint8_t on)
+{
+	low_side_on = on;
+}
+
+uint16_t HB_GetTarget(void)
+{
+	return target;
+}
+
+void HB_UpdateOutput(uint16_t supply)
+{
+	uint16_t temp_dc = CalculateDuty16b(target, supply);
+	
+	HB_SetDirect(temp_dc);
+}
+
+void HB_SetDirect(uint16_t duty)
+{
+	/// Limit duty cycle
+	if(duty > max_dc) active_dc = max_dc;
+	else if(duty < min_dc) active_dc = 0;
+	else active_dc = duty;
+	
+	// Set duty cycle
+	if(!is_en) return;
+	HAL_Coil_SetLowSide(low_side_on);
+	HAL_Coil_SetPWM16b(active_dc);
+}
+
+uint8_t HB_IsLowOn(void)
+{
+	if(HAL_ReadLvl_CoilLow() == HIGH) return 1;
+	else return 0;
+}
+
+void HB_Enable(void)
+{
+	// Restore low side
+	if(low_side_on) HAL_Coil_SetLowSide(1);
+	// Restore duty cycle
+	HAL_Coil_SetPWM(active_dc);
+	is_en = 1;
+}
+
+void HB_Disable(void)
+{
+	// Set 0 DC
+	HAL_Coil_SetPWM(0);
+	// Disable low side
+	HAL_Coil_SetLowSide(0);
+	is_en = 0;
+}
+
+uint8_t HB_IsEnabled(void)
+{
+	if(is_en) return 1;
+	else return 0;
+}
+
+int8_t HB_IsOutputMatch(uint16_t fb_output_voltage, uint16_t limit)
+{
+	// No fault if output not enabled
+	if(!is_en) return -1;
+	
+	// Can't check voltage if low side is off
+	if(!low_side_on) return -1;
+	
+	if(target==0)
+	{
+		// Output can be only 0
+		if(fb_output_voltage != 0) return 0;
+		else return 1;
+	};
+	
+	// Calculate upper and lower bounds
+	uint16_t max = target + limit;
+	uint16_t min = target - limit;
+	
+	//Sanity check
+	if(max < target) max = 0xFFFF;
+	if(min > target) min = 0;
+	
+	//Do check
+	if((fb_output_voltage < min)||(fb_output_voltage > max)) return 0;
+	else return 1;
+}
+
+/**** Private function definitions ****/
+static uint16_t CalculateDuty16b(uint16_t target, uint16_t supply)
+{
+	if(target==0) return 0;
+	if(supply==0) return 0;
+	if(target > supply) return 0xFFFF;
+	
+	// Calculate Duty cycle, in 16bit format
+	uint32_t temp = (uint32_t)target * 0x0000FFFF;
+	temp = temp / supply;
+	
+	//Limit output to 16 bits
+	if(temp > 0x0000FFFF) return 0xFFFF;
+	else return (uint16_t)temp;	
+}

firmware/devices/halfbridge.h

@@ -0,0 +1,24 @@
+#ifndef HALFBRIDGE_H_
+#define HALFBRIDGE_H_
+
+/**** Includes ****/
+#include <stdint.h>
+
+/**** Public function declarations ****/
+void HB_UpdateOutput(uint16_t supply);
+
+void HB_SetTarget(uint16_t voltage);
+void HB_SetLowSide(uint8_t on);
+
+void HB_SetDirect(uint16_t duty);
+
+void HB_Enable(void);
+void HB_Disable(void);
+
+uint16_t HB_GetTarget(void);
+
+uint8_t HB_IsLowOn(void);
+uint8_t HB_IsEnabled(void);
+int8_t HB_IsOutputMatch(uint16_t fb_output_voltage, uint16_t limit);
+
+#endif /* HALFBRIDGE_H_ */

firmware/devices/inputs.c

@@ -0,0 +1,82 @@
+/**** Includes ****/
+#include "hal/udccd_hal.h"
+#include "inputs.h"
+
+/**** Private definitions ****/
+
+/**** Private variables ****/
+static const uint8_t def_debounce_lim = 10;
+
+/**** Private function declarations ****/
+static void InitDefaultInput(inCh_t* inp);
+static void ProcessInput(uint8_t read_lvl, inCh_t* inp);
+
+/**** Public function definitions ****/
+void Inputs_DefInit(inputs_t* inputs)
+{
+	InitDefaultInput(&inputs->handbrake);
+	InitDefaultInput(&inputs->brakes);
+	InitDefaultInput(&inputs->dimm);
+	InitDefaultInput(&inputs->up);
+	InitDefaultInput(&inputs->down);
+	InitDefaultInput(&inputs->mode);
+}
+
+void Inputs_UpdateAll(inputs_t* inputs)
+{
+	// Chassis inputs
+	ProcessInput(HAL_ReadLvl_Handbrake(), &inputs->handbrake);
+	ProcessInput(HAL_ReadLvl_Brake(), &inputs->brakes);
+	ProcessInput(HAL_ReadLvl_Dimm(), &inputs->dimm);
+
+	// User inputs
+	ProcessInput(HAL_ReadLvl_BtnUp(), &inputs->up);
+	ProcessInput(HAL_ReadLvl_BtnDown(), &inputs->down);
+	ProcessInput(HAL_ReadLvl_BtnMode(), &inputs->mode);
+}
+
+void Inputs_SetHanbrakePullUp(uint8_t on)
+{
+	if(on) HAL_SetPull_Handbrake(HIGH);
+	else HAL_SetPull_Handbrake(HIZ);
+}
+
+/**** Private function definitions ****/
+static void InitDefaultInput(inCh_t* inp)
+{
+	inp->is_active = 0;
+	inp->is_new = 0;
+	inp->state_timer = 0;
+	inp->cfg.act_level = LOW;
+	inp->cfg.dbnc_treshold = def_debounce_lim;
+	inp->proc.level = LOW;
+	inp->proc.dbnc_counter = 0;
+}
+
+static void ProcessInput(uint8_t read_lvl, inCh_t* inp)
+{
+	if(inp->state_timer < 0xFFFF) inp->state_timer++;
+	
+	if(read_lvl != inp->proc.level)
+	{
+		//Debounce ongoing
+		inp->proc.dbnc_counter++;
+		if(inp->proc.dbnc_counter < inp->cfg.dbnc_treshold) return;
+		
+		//Save level
+		inp->proc.level = read_lvl;
+		//Change state
+		if(inp->proc.level == inp->cfg.act_level) inp->is_active = 1;
+		else inp->is_active = 0;
+		// Update new flag
+		inp->is_new = 1;
+		// Reset state timer
+		inp->state_timer = 0;
+		return;
+	}
+	else
+	{
+		//Debounce failed
+		if(inp->proc.dbnc_counter) inp->proc.dbnc_counter = 0;
+	}
+}

firmware/devices/inputs.h

@@ -0,0 +1,43 @@
+#ifndef INPUTS_H_
+#define INPUTS_H_
+
+/**** Includes ****/
+#include <stdint.h>
+#include "common/level.h"
+
+/**** Public definitions ****/
+typedef struct {
+	level_t act_level;
+	uint8_t dbnc_treshold;
+} inChCfg_t;
+
+typedef struct {
+	level_t level;
+	uint8_t dbnc_counter;
+} inChRaw_t;
+
+typedef struct {
+	uint8_t is_active;
+	uint8_t is_new;
+	uint16_t state_timer;
+	inChRaw_t proc;
+	inChCfg_t cfg;
+} inCh_t;
+
+typedef struct {
+	inCh_t handbrake;
+	inCh_t brakes;
+	inCh_t dimm;
+	inCh_t up;
+	inCh_t down;
+	inCh_t mode;
+} inputs_t;
+
+/**** Public function declarations ****/
+void Inputs_DefInit(inputs_t* inputs);
+
+void Inputs_UpdateAll(inputs_t* inputs);
+
+void Inputs_SetHanbrakePullUp(uint8_t on);
+
+#endif /* INPUTS_H_ */

firmware/devices/led_display.c

@@ -0,0 +1,20 @@
+/**** Includes ****/
+#include "hal/udccd_hal.h"
+#include "led_display.h"
+
+/**** Private variables ****/
+
+/**** Private function declarations ****/
+
+/**** Public function definitions ****/
+void LED_DSP_ShowImage(uint8_t image)
+{
+	HAL_LEDS_Set(image);
+}
+
+void LED_DSP_SetBrightness(uint8_t percent)
+{
+	HAL_LEDS_SetPWM(percent);
+}
+
+/**** Private function definitions ****/

firmware/devices/led_display.h

@@ -0,0 +1,13 @@
+#ifndef LED_DISPLAY_H_
+#define LED_DISPLAY_H_
+
+/**** Includes ****/
+#include <stdint.h>
+
+/**** Public definitions ****/
+
+/**** Public function declarations ****/
+void LED_DSP_ShowImage(uint8_t image);
+void LED_DSP_SetBrightness(uint8_t percent);
+
+#endif /* LED_DISPLAY_H_ */

firmware/devices/memory.c

@@ -0,0 +1,34 @@
+/**** Includes ****/
+#include <avr/eeprom.h>
+#include "memory.h"
+
+/**** Public function definitions ****/
+uint8_t MEM_Read8b(uint8_t address)
+{
+	return eeprom_read_byte((uint8_t*)address);
+}
+
+uint16_t MEM_Read16b(uint8_t address)
+{
+	return eeprom_read_word((uint8_t*)address);
+}
+
+uint32_t MEM_Read32b(uint8_t address)
+{
+	return eeprom_read_dword((uint8_t*)address);
+}
+
+void MEM_Write8b(uint8_t address, uint8_t value)
+{
+	return eeprom_write_byte((uint8_t*)address, value);
+}
+
+void MEM_Write16b(uint8_t address, uint16_t value)
+{
+	return eeprom_write_word((uint8_t*)address, value);
+}
+
+void MEM_Write32b(uint8_t address, uint32_t value)
+{
+	return eeprom_write_dword((uint8_t*)address, value);
+}

firmware/devices/memory.h

@@ -0,0 +1,16 @@
+#ifndef MEMORY_H_
+#define MEMORY_H_
+
+/**** Includes ****/
+#include <stdint.h>
+
+/**** Public function declarations ****/
+uint8_t MEM_Read8b(uint8_t address);
+uint16_t MEM_Read16b(uint8_t address);
+uint32_t MEM_Read32b(uint8_t address);
+
+void MEM_Write8b(uint8_t address, uint8_t value);
+void MEM_Write16b(uint8_t address, uint16_t value);
+void MEM_Write32b(uint8_t address, uint32_t value);
+
+#endif /* MEMORY_H_ */

firmware/drivers/display.c

@@ -0,0 +1,125 @@
+/**** Includes ****/
+#include "display.h"
+
+/**** Private definitions ****/
+
+/**** Private variables ****/
+static uint8_t PWM_DIMM = 50;
+static uint8_t PWM_BRIGTH = 100;
+
+static uint8_t set_image = 0x00;
+
+static uint16_t lock_timer = 0;
+
+/**** Private function declarations ****/
+static uint8_t ImageGen_Dot10(uint8_t percent);
+static uint8_t ImageGen_Dot20(uint8_t percent);
+static uint8_t ImageGen_Bar(uint8_t percent);
+
+/**** Public function definitions ****/
+void Display_CfgBacklight(uint8_t brigth, uint8_t dimm)
+{
+	//Limit values
+	if(brigth>100) brigth = 100;
+	else if(brigth==0) brigth = 1;
+	
+	if(dimm>100) dimm = 100;
+	else if(dimm==0) dimm = 1;
+	
+	//Save values
+	PWM_BRIGTH = brigth;
+	PWM_DIMM = dimm;
+}
+
+void Display_SetImage(uint8_t image)
+{
+	if(lock_timer) return;
+	
+	set_image = image & 0x3F;
+}
+
+void Display_SetPercent(uint8_t value, dspStyle_t style)
+{
+	switch(style)
+	{
+		case BAR:
+		Display_SetImage(ImageGen_Bar(value));
+		break;
+		
+		case DOT10:
+		Display_SetImage(ImageGen_Dot10(value));
+		break;
+		
+		default:
+		Display_SetImage(ImageGen_Dot20(value));
+		break;
+	}
+}
+
+void Display_SetScale(uint16_t value, uint16_t max_value ,dspStyle_t style)
+{
+	//Convert value to percent
+	uint32_t temp = (uint32_t)value *100;
+	temp /= max_value;
+	
+	//Limit value to 100 percent
+	uint8_t percent = 0;
+	if(temp >= 100) percent = 100;
+	else if(temp == 0) percent = 0;
+	else percent = (uint8_t)temp;
+	
+	Display_SetPercent(percent, style);
+}
+
+void Display_SetLock(uint16_t time)
+{
+	lock_timer = time;
+}
+
+void Display_Update(inputs_t* inputs)
+{
+	// Brightness control
+	if(inputs->dimm.is_active) LED_DSP_SetBrightness(PWM_DIMM);
+	else LED_DSP_SetBrightness(PWM_BRIGTH);
+	
+	if(lock_timer) lock_timer--;
+
+	// Set image
+	LED_DSP_ShowImage(set_image);
+}
+
+/**** Private function definitions ****/
+static uint8_t ImageGen_Dot10(uint8_t percent)
+{
+	if(percent<6) return 0x01;
+	else if(percent<16) return 0x03;
+	else if(percent<26) return 0x02;
+	else if(percent<36) return 0x06;
+	else if(percent<46) return 0x04;
+	else if(percent<56) return 0x0C;
+	else if(percent<66) return 0x08;
+	else if(percent<76) return 0x18;
+	else if(percent<86) return 0x10;
+	else if(percent<96) return 0x30;
+	else return 0x20;
+}
+
+static uint8_t ImageGen_Dot20(uint8_t percent)
+{
+	if(percent<11) return 0x01;
+	else if(percent<31) return 0x02;
+	else if(percent<51) return 0x04;
+	else if(percent<71) return 0x08;
+	else if(percent<91) return 0x10;
+	else return 0x20;
+}
+
+static uint8_t ImageGen_Bar(uint8_t percent)
+{
+	if(percent<11) return 0x01;
+	else if(percent<31) return 0x03;
+	else if(percent<51) return 0x07;
+	else if(percent<71) return 0x0F;
+	else if(percent<91) return 0x1F;
+	else return 0x3F;
+}

firmware/drivers/display.h

@@ -0,0 +1,27 @@
+#ifndef DISPLAY_DRV_H_
+#define DISPLAY_DRV_H_
+
+/**** Includes ****/
+#include <avr/io.h>
+#include "../devices/led_display.h"
+#include "../devices/inputs.h"
+
+/**** Public definitions ****/
+typedef enum {
+	DOT20,
+	DOT10,
+	BAR
+} dspStyle_t;
+
+/**** Public function declarations ****/
+void Display_SetImage(uint8_t image);
+void Display_SetPercent(uint8_t value, dspStyle_t style);
+void Display_SetScale(uint16_t value, uint16_t max_value ,dspStyle_t style);
+
+void Display_SetLock(uint16_t time);
+
+void Display_Update(inputs_t* inputs);
+
+void Display_CfgBacklight(uint8_t brigth, uint8_t dimm);
+
+#endif /* DISPLAY_DRV_H_ */

firmware/drivers/output.c

@@ -0,0 +1,341 @@
+/**** Includes ****/
+#include "output.h"
+
+/**** Private definitions ****/
+typedef struct {
+	uint8_t active;
+	uint8_t time;
+} warn_t;
+
+typedef struct {
+	warn_t supply_voltage;
+	warn_t supply_current;
+	warn_t supply_power;
+	warn_t output_voltage;
+	warn_t output_current;
+	warn_t output_power;
+	warn_t output_open;
+	warn_t output_short;
+	warn_t output_mismatch;
+} warnings_t;
+
+typedef struct {
+	uint8_t supply_uvlo;
+	uint8_t supply_ovp;
+	uint8_t supply_ocp;
+	uint8_t supply_opp;
+	uint8_t output_ovp;
+	uint8_t output_ocp;
+	uint8_t output_opp;
+	uint8_t output_open;
+	uint8_t output_short;
+} faults_t;
+
+/**** Private constants ****/
+static const uint16_t LIM_SUPPLY_UVLO =  8000; //mV
+static const uint16_t LIM_SUPPLY_OVP  = 18000; //mV
+static const uint16_t LIM_SUPPLY_OCP  =  7000; //mA
+static const uint16_t LIM_SUPPLY_OPP  = 40000; //mW
+
+static const uint16_t LIM_OUTPUT_OVP = 12000;  //mV
+static const uint16_t LIM_OUTPUT_OCP =  7000;  //mA
+static const uint16_t LIM_OUTPUT_OPP = 40000;  //mW
+
+static const uint16_t LIM_OUTPUT_OPEN = 40000; //mR
+static const uint16_t LIM_OUTPUT_SHORT =  750; //mR
+
+static const uint16_t LIM_OUTPUT_MATCH = 100; //mV
+
+static const uint8_t OCP_WARNING_LIMIT   = 10; //cycles
+static const uint8_t SHORT_WARNING_LIMIT = 50; //cycles
+
+static const uint16_t MAX_OUTPUT_VOLTAGE = 10000; //mV
+static const uint16_t MIN_OUTPUT_VOLTAGE  =  100; //mV
+
+static const uint16_t COOLDOWN_TIME = 5000;
+
+/**** Private variables ****/
+static warnings_t warnings;
+static faults_t faults;
+
+static uint16_t target_output = 0;
+static uint16_t adj_target = 0;
+
+static int32_t hb_volt_sum = 0;
+
+static uint8_t new_target = 1;
+
+static uint8_t steady_state = 0;
+
+static faultState_t fault_state = F_NONE;
+
+static uint16_t cooldown_timer = 0;
+
+static outState_t out_state = O_OFF;
+
+/**** Private function declarations ****/
+static void Process_Warnings(analog_t* meas);
+static uint8_t Process_Faults(void);
+
+static void ProcessWarningTime(warn_t* w);
+static uint8_t isAnyFaultActive(faults_t* f);
+static uint8_t isFaultWarningActive(warnings_t* w, faults_t* f);
+static void ResetFaults(faults_t* f);
+
+/**** Public function definitions ****/
+void Output_Enable(void)
+{
+	ResetFaults(&faults);
+	target_output = 0;
+	out_state = O_ACTIVE;
+	HB_SetTarget(0) ;
+	HB_SetLowSide(1);
+	HB_Enable();
+}
+
+void Output_Update(analog_t* meas)
+{	
+	Process_Warnings(meas);
+	
+	// Convert Warnings to Faults
+	uint8_t active_fault = Process_Faults();
+	
+	/// Ignore faults
+	active_fault = 0;
+	
+	// Determine coil state	
+	switch(out_state)
+	{
+		case O_ACTIVE:
+		if(active_fault)
+		{
+			// Disable output
+			HB_Disable();
+			out_state = O_FAULTED;
+			break;
+		};
+		
+		//Do target adjustment logic
+		if(steady_state >= 10)
+		{
+			//Calculate average HB voltage
+			hb_volt_sum /= 11;
+			
+			// Calculate feedback adjusted HB output
+			int32_t error = hb_volt_sum - (int32_t)target_output;
+			int32_t temp = (int32_t)adj_target - error;
+			// Limit to 16bits
+			if(temp<=0) adj_target = 0;
+			else if(temp >= 0x0000FFFF) adj_target = 0xFFFF;
+			else adj_target = (uint16_t)temp;
+			steady_state = 0;
+			hb_volt_sum = 0;
+		}
+		else
+		{
+			hb_volt_sum += meas->hb_voltage;
+			steady_state++;
+		}
+		
+		// Closed loop or open loop target set
+		if(new_target)
+		{
+			// Set open-loop HB output
+			HB_SetTarget(target_output);
+			adj_target = target_output;
+			steady_state = 0;
+			new_target = 0;
+			hb_volt_sum = 0;
+		}
+		else
+		{
+			HB_SetTarget(adj_target);
+		}
+
+		// Update output
+		HB_UpdateOutput(meas->supply_voltage);
+		break;
+		
+		case O_FAULTED:
+		if(!active_fault)
+		{
+			//Return to normal state
+			HB_Enable();
+			out_state = O_ACTIVE;
+		}
+		break;
+		
+		default:  //OFF
+		if(HB_IsEnabled()) HB_Disable();
+		break;
+	}
+}
+
+void Output_SetTarget(uint16_t voltage)
+{
+	if(voltage > MAX_OUTPUT_VOLTAGE) voltage = MAX_OUTPUT_VOLTAGE;
+	else if((voltage > 0)&&(voltage < MIN_OUTPUT_VOLTAGE)) voltage = MIN_OUTPUT_VOLTAGE;
+	
+	if(voltage != target_output) new_target = 1;
+	target_output = voltage;
+}
+
+outState_t Output_GetOutputState(void)
+{
+	return out_state;
+}
+
+/**** Private function definitions ****/
+static void Process_Warnings(analog_t* meas)
+{
+	// Supply UVLO and OVP
+	if((meas->supply_voltage > LIM_SUPPLY_OVP)||(meas->supply_voltage < LIM_SUPPLY_UVLO)) warnings.supply_voltage.active = 1;
+	else warnings.supply_voltage.active = 0;
+	
+	// Supply OCP
+	if(meas->supply_current > LIM_SUPPLY_OCP) warnings.supply_current.active = 1;
+	else warnings.supply_current.active = 0;
+	
+	// Supply OPP
+	if(meas->supply_power > LIM_SUPPLY_OPP) warnings.supply_power.active = 1;
+	else warnings.supply_power.active = 0;
+	
+	// Halfbridge output conditions
+	// Output Target mismatch
+	if(HB_IsOutputMatch(meas->hb_voltage, LIM_OUTPUT_MATCH) == 0) warnings.output_mismatch.active = 1;
+	else warnings.output_mismatch.active = 0;
+	
+	// Output OCP
+	if((HB_IsLowOn())&&(meas->hb_currnet > LIM_OUTPUT_OCP)) warnings.output_current.active = 1;
+	else warnings.output_current.active = 0;
+	
+	// Output OVP
+	if((HB_IsLowOn())&&(meas->hb_voltage > LIM_OUTPUT_OVP)) warnings.output_voltage.active = 1;
+	else warnings.output_voltage.active = 0;
+	
+	// Output OPP
+	if((HB_IsEnabled())&&(meas->hb_power > LIM_OUTPUT_OPP)) warnings.output_power.active = 1;
+	else warnings.output_power.active = 0;
+	
+	// Output Short
+	if((HB_IsEnabled())&&(meas->hb_resistance < LIM_OUTPUT_SHORT)) warnings.output_short.active = 1;
+	else warnings.output_short.active = 0;
+	
+	// Output Open - Load loss
+	if((HB_IsEnabled())&&(meas->hb_resistance > LIM_OUTPUT_OPEN)) warnings.output_open.active = 1;
+	else warnings.output_open.active = 0;
+	
+	ProcessWarningTime(&warnings.supply_voltage);
+	ProcessWarningTime(&warnings.supply_current);
+	ProcessWarningTime(&warnings.supply_power);
+	ProcessWarningTime(&warnings.output_mismatch);
+	ProcessWarningTime(&warnings.output_voltage);
+	ProcessWarningTime(&warnings.output_current);
+	ProcessWarningTime(&warnings.output_power);
+	ProcessWarningTime(&warnings.output_open);
+	ProcessWarningTime(&warnings.output_short);
+}
+
+static uint8_t Process_Faults(void)
+{
+	// Check warnings to escalate to fault	
+	// Supply OCP
+	if(warnings.supply_current.time > OCP_WARNING_LIMIT) faults.supply_ocp = 1;
+	
+	// Output OCP
+	if(warnings.output_current.time > OCP_WARNING_LIMIT) faults.output_ocp = 1;
+	
+	// Output short
+	if(warnings.output_short.time > SHORT_WARNING_LIMIT) faults.output_short = 1;
+	
+	switch(fault_state)
+	{	
+		case F_ACTIVE:
+		// Check if fault still active
+		if(!isFaultWarningActive(&warnings, &faults))
+		{
+			// Fault cause ended, go to cooldown
+			cooldown_timer = COOLDOWN_TIME;
+			fault_state = F_COOLDOWN;
+		};
+		break;
+		
+		case F_COOLDOWN:
+		// Check if fault reoccurs
+		if(isFaultWarningActive(&warnings, &faults))
+		{
+			fault_state = F_ACTIVE;
+			break;
+		};
+
+		// Wait for cooldown timer, reset fault flags
+		if(cooldown_timer) cooldown_timer--;
+		else
+		{
+			ResetFaults(&faults);
+			fault_state = F_NONE;
+		}
+		break;
+		
+		default: //NONE
+		// Check for new faults
+		if(isAnyFaultActive(&faults))
+		{
+			// Start fault process
+			fault_state = F_ACTIVE;
+		};
+		break;
+	}
+	
+	if(fault_state != F_NONE) return 1;
+	else return 0;
+}
+
+static void ProcessWarningTime(warn_t* w)
+{
+	if((w->active)&&(w->time < 0xFF)) w->time++;
+	else if(w->active == 0) w->time = 0;
+}
+
+static uint8_t isAnyFaultActive(faults_t* f)
+{
+	if(f->supply_uvlo) return 1;
+	if(f->supply_ovp) return 1;
+	if(f->supply_ocp) return 1;
+	if(f->supply_opp) return 1;
+	if(f->output_ovp) return 1;
+	if(f->output_ocp) return 1;
+	if(f->output_opp) return 1;
+	if(f->output_open) return 1;
+	if(f->output_short) return 1;
+	
+	return 0;
+}
+
+static uint8_t isFaultWarningActive(warnings_t* w, faults_t* f)
+{
+	if((f->supply_uvlo)  && (w->supply_voltage.active)) return 1;
+	if((f->supply_ovp)   && (w->supply_voltage.active)) return 1;
+	if((f->supply_ocp)   && (w->supply_current.active)) return 1;
+	if((f->supply_opp)   && (w->supply_power.active)  ) return 1;
+	if((f->output_ovp)   && (w->output_voltage.active)) return 1;
+	if((f->output_ocp)   && (w->output_current.active)) return 1;
+	if((f->output_opp)   && (w->output_power.active)  ) return 1;
+	if((f->output_open)  && (w->output_open.active)   ) return 1;
+	if((f->output_short) && (w->output_short.active)  ) return 1;
+	
+	return 0;
+}
+
+static void ResetFaults(faults_t* f)
+{
+	f->supply_uvlo = 0;
+	f->supply_ovp = 0;
+	f->supply_ocp = 0;
+	f->supply_opp = 0;
+	f->output_ovp = 0;
+	f->output_ocp = 0;
+	f->output_opp = 0;
+	f->output_open = 0;
+	f->output_short = 0;
+}

firmware/drivers/output.h

@@ -0,0 +1,30 @@
+#ifndef OUTPUT_DRV_H_
+#define OUTPUT_DRV_H_
+
+/**** Includes ****/
+#include <avr/io.h>
+#include "../devices/analog.h"
+#include "../devices/halfbridge.h"
+
+/**** Public definitions ****/
+typedef enum {
+	F_NONE,
+	F_ACTIVE,
+	F_COOLDOWN
+} faultState_t;
+
+typedef enum {
+	O_OFF,
+	O_ACTIVE,
+	O_FAULTED
+} outState_t;
+
+/**** Public function declarations ****/
+void Output_Enable(void);
+void Output_Update(analog_t* meas);
+
+void Output_SetTarget(uint16_t voltage);
+
+outState_t Output_GetOutputState(void);
+
+#endif /* OUTPUT_DRV_H_ */

firmware/logic/coil.c

@@ -0,0 +1,127 @@
+/**** Includes ****/
+#include "coil.h"
+
+/**** Private definitions ****/
+
+/**** Private constants ****/
+
+/**** Private variables ****/
+static uint16_t lock_current = 4500; //mA
+static uint16_t min_current = 100; //mA
+static uint16_t target_current = 0; //mA
+static uint8_t new_target = 1;
+
+static uint16_t adj_target_current = 0; //mA
+static uint16_t target_voltage = 0; //mV
+
+static uint8_t act_force = 0;
+
+static uint16_t nominal_resitance = 1500; //mR
+
+static int32_t sum_current = 0;
+static uint8_t sum_cnt = 0;
+
+
+/**** Private function declarations ****/
+static uint16_t UpdateVoltage(uint16_t cur, uint16_t res);
+
+/**** Public function definitions ****/
+void Coil_SetLockCurrent(uint16_t lock_i)
+{
+	lock_current = lock_i;
+}
+
+void Coil_SetTarget_Force(uint8_t force)
+{
+	// Check if worth doing
+	if(force == act_force) return;
+	
+	// Calculate new target current
+	act_force = force;
+	
+	// Check simple answer
+	uint16_t new_current = 0;
+	if(force==0) new_current = 0;
+	else if(force >= 100) new_current = lock_current;
+	else
+	{
+		uint32_t temp = (uint32_t)force * lock_current;
+		temp /= 100;
+		
+		if(temp > 0x0000FFFF) new_current = lock_current;
+		else new_current = (uint16_t) temp;
+	}
+	
+	// Update new target
+	Coil_SetTarget_Current(new_current);
+}
+
+void Coil_SetTarget_Current(uint16_t current)
+{
+	if(current >= lock_current) current = lock_current;
+	else if((current > 0)&&(current <= min_current)) current = min_current;
+	
+	if(current != target_current) new_target = 1;
+	target_current = current;
+}
+
+uint16_t Coil_GetTargetVolatge(void)
+{
+	return target_voltage;
+}
+
+uint16_t Coil_Update(analog_t* meas)
+{
+	// Collect average current
+	sum_current += meas->hb_currnet;
+	sum_cnt++;
+	
+	// Update measurement
+	if(sum_cnt >= 10)
+	{
+		// Calculate average
+		sum_current /= sum_cnt;
+		
+		// Calculate error
+		int32_t error = sum_current - (int32_t)target_current;
+		int32_t temp = (int32_t)adj_target_current - error;
+		
+		// Limit to 16bits
+		if(temp<0) adj_target_current = 0;
+		else if(temp > 0x0000FFFF) adj_target_current = 0xFFFF;
+		else adj_target_current = (uint16_t)temp;
+		sum_cnt = 0;
+		sum_current = 0;
+	};
+	
+	// Closed loop or open loop target set
+	if(new_target)
+	{
+		// Set open-loop HB output
+		target_voltage = UpdateVoltage(target_current, nominal_resitance);
+		adj_target_current = target_current;
+		new_target = 0;
+		sum_cnt = 0;
+		sum_current = 0;
+	}
+	else
+	{
+		target_voltage = UpdateVoltage(adj_target_current, nominal_resitance);
+	}
+	
+	return target_voltage;
+}
+	
+/**** Private function definitions ****/
+static uint16_t UpdateVoltage(uint16_t cur, uint16_t res)
+{
+	// Update settable voltage
+	if(cur==0) return 0;
+	else
+	{
+		uint32_t volt = (uint32_t)cur * res;
+		volt /= 1000;
+		if(volt > 0x0000FFFF) return 0xFFFF;
+		else return (uint16_t)volt;
+	}
+}

firmware/logic/coil.h

@@ -0,0 +1,19 @@
+#ifndef COIL_LOGIC_H_
+#define COIL_LOGIC_H_
+
+/**** Includes ****/
+#include <stdint.h>
+#include "../devices/analog.h"
+
+/**** Public definitions ****/
+
+/**** Public function declarations ****/
+void Coil_SetTarget_Force(uint8_t force);
+void Coil_SetTarget_Current(uint16_t current);
+uint16_t Coil_GetTargetVolatge(void);
+
+uint16_t Coil_Update(analog_t* meas);
+
+void Coil_SetLockCurrent(uint16_t lock_i);
+
+#endif /* COIL_LOGIC_H_ */

firmware/logic/force.c

@@ -0,0 +1,186 @@
+/**** Includes ****/
+#include "force.h"
+
+/**** Private definitions ****/
+
+/**** Private constants ****/
+static const int8_t BUTTONS_STEP = 10;
+static const uint16_t BUTTON_HOLD_TIME = 250;
+static const uint16_t MODE_HOLD_TIME = 500;
+
+/**** Private variables ****/
+static inputMode_t input_mode = IM_BUTTONS;
+
+static uint8_t user_force = 0;
+static uint8_t new_user_force = 0;
+
+static brakeMode_t brake_mode = BM_OPEN;
+static uint8_t new_brake_mode = 1;
+
+/**** Private function declarations ****/
+static uint8_t SaturatedAdd(uint8_t base, int8_t delta);
+
+/**** Public function definitions ****/
+inputMode_t Force_GetInputMode(void)
+{
+	return input_mode;
+}
+
+void Force_CfgInputMode(inputMode_t in_mode)
+{
+	input_mode = in_mode;
+}
+
+void Force_SetUserForce(uint8_t force)
+{
+	if(force > 100) force = 100;
+	user_force = force;
+}
+
+void Force_SetBrakeMode(uint8_t bmode)
+{
+	brake_mode = bmode;
+}
+
+uint8_t Force_Update(inputs_t* inputs, analog_t* meas)
+{
+	// Process user inputs
+	if(input_mode==IM_POT)
+	{
+		// Process potentiometer
+		if(meas->pot_voltage <= 500) user_force = 0;
+		else if(meas->pot_voltage >= 4500 ) user_force = 100;
+		else
+		{
+			uint16_t pot_u = meas->pot_voltage;
+			pot_u /= 50;
+			
+			//Limit to 100
+			if(pot_u > 100) user_force = 100;
+			else if(pot_u < 10) user_force = 10;
+			else user_force = (uint8_t)pot_u;
+		}
+	}
+	else
+	{
+		// Process +/- timer
+		if((inputs->down.is_active)&&(inputs->down.state_timer > BUTTON_HOLD_TIME))
+		{
+			inputs->down.is_new = 1;
+			inputs->down.state_timer = 0;
+		};
+		
+		if((inputs->up.is_active)&&(inputs->up.state_timer > BUTTON_HOLD_TIME))
+		{
+			inputs->up.is_new = 1;
+			inputs->up.state_timer = 0;
+		};
+		
+		// Process +/- logic
+		if((inputs->down.is_new)&&(inputs->down.is_active))
+		{
+			user_force = SaturatedAdd(user_force, -1 * BUTTONS_STEP);
+			new_user_force = 1;
+		}
+		else if((inputs->up.is_new)&&(inputs->up.is_active))
+		{
+			user_force = SaturatedAdd(user_force, BUTTONS_STEP);
+			new_user_force = 1;
+		};
+		
+		inputs->down.is_new = 0;
+		inputs->up.is_new = 0;
+	}
+	
+	// Process mode timer
+	if((inputs->mode.is_active)&&(inputs->mode.state_timer > MODE_HOLD_TIME))
+	{
+		inputs->mode.is_new = 1;
+		inputs->mode.state_timer = 0;
+	};
+	
+	// Process mode logic
+	if((inputs->mode.is_new)&&(inputs->mode.is_active))
+	{
+		//Cycle mode
+		switch(brake_mode)
+		{
+			case BM_OPEN:
+			brake_mode = BM_KEEP;
+			break;
+			
+			case BM_KEEP:
+			brake_mode = BM_LOCK;
+			break;
+			
+			case BM_LOCK:
+			brake_mode = BM_OPEN;
+			break;
+			
+			default:
+			brake_mode = BM_OPEN;
+			break;
+		}
+		new_brake_mode = 1;
+	};
+	inputs->mode.is_new = 0;
+	
+	
+	// Determine next target force from inputs
+	if(inputs->handbrake.is_active)
+	{
+		return 0;
+	}
+	else if(inputs->brakes.is_active)
+	{
+		switch(brake_mode)
+		{
+			case BM_LOCK:
+			return 100;
+			
+			case BM_KEEP:
+			return user_force;
+			
+			default:
+			return 0;
+		}
+	}
+	else
+	{
+		return user_force;
+	}
+}
+
+uint8_t Force_IsNewUserForce(void)
+{
+	return new_user_force;
+}
+
+void Force_ResetNewUserForce(void)
+{
+	new_user_force = 0;
+}
+
+brakeMode_t Force_GetBrakeMode(void)
+{
+	return brake_mode;
+}
+
+uint8_t Force_IsNewBrakeMode(void)
+{
+	return new_brake_mode;
+}
+
+void Force_ResetNewBrakeMode(void)
+{
+	new_brake_mode = 0;
+}
+
+/**** Private function definitions ****/
+static uint8_t SaturatedAdd(uint8_t base, int8_t delta)
+{
+	int16_t temp = (int16_t)base + delta;
+	if(temp < 0) return 0;
+	else if(temp >= 100) return 100;
+	else return (uint8_t)temp;
+}

firmware/logic/force.h

@@ -0,0 +1,36 @@
+#ifndef FORCE_LOGIC_H_
+#define FORCE_LOGIC_H_
+
+/**** Includes ****/
+#include <stdint.h>
+#include "../devices/analog.h"
+#include "../devices/inputs.h"
+
+/**** Public definitions ****/
+typedef enum {
+	BM_OPEN,
+	BM_KEEP,
+	BM_LOCK
+} brakeMode_t;
+
+typedef enum {
+	IM_BUTTONS,
+	IM_POT
+} inputMode_t;
+
+/**** Public function declarations ****/
+void Force_CfgInputMode(inputMode_t in_mode);
+inputMode_t Force_GetInputMode(void);
+
+uint8_t Force_Update(inputs_t* inputs, analog_t* meas);
+
+void Force_SetBrakeMode(uint8_t bmode);
+brakeMode_t Force_GetBrakeMode(void);
+uint8_t Force_IsNewBrakeMode(void);
+void Force_ResetNewBrakeMode(void);
+
+void Force_SetUserForce(uint8_t force);
+uint8_t Force_IsNewUserForce(void);
+void Force_ResetNewUserForce(void);
+
+#endif /* FORCE_LOGIC_H_ */

firmware/logic/settings.c

@@ -0,0 +1,184 @@
+/**** Includes ****/
+#include "settings.h"
+
+/**** Private definitions ****/
+
+/**** Private constants ****/
+static const uint8_t addr_force = 0x01;
+static const uint8_t addr_bmode = 0x02;
+static const uint8_t addr_inmode = 0x03;
+
+static const uint8_t addr_dsp_bright = 0x04;
+static const uint8_t addr_dsp_dimm = 0x05;
+
+static const uint8_t addr_lock_amps = 0x06;
+
+/**** Private variables ****/
+static uint16_t save_force_timer = 0;
+static uint16_t save_bmode_timer = 0;
+
+/**** Private function declarations ****/
+
+/**** Public function definitions ****/
+void Setings_Update(uint8_t is_new_force, uint8_t force, uint8_t is_new_bmode, brakeMode_t bmode)
+{
+	if(is_new_force) save_force_timer = 5000;
+	
+	if(is_new_bmode) save_bmode_timer = 5000;
+	
+	if(save_force_timer)
+	{
+		save_force_timer--;
+		if(!save_force_timer)
+		{
+			// Save force setting
+			Setings_SaveForce(force);
+		};
+	};
+	
+	if(save_bmode_timer)
+	{
+		save_bmode_timer--;
+		if(!save_bmode_timer)
+		{
+			// Save mode setting
+			Setings_SaveBrakeMode(bmode);
+		};
+	};
+}
+
+
+void Setings_SaveForce(uint8_t value)
+{
+	MEM_Write8b(addr_force, value);
+}
+
+uint8_t Setings_GetForce(void)
+{
+	uint8_t val = MEM_Read8b(addr_force);
+	if(val > 100) return 0;
+	else return val;
+}
+
+
+void Setings_SaveBrakeMode(brakeMode_t bmode)
+{
+	// Convert and save input mode setting
+	// Convert and save mode setting
+	uint8_t val = 0x00;
+	switch(bmode)
+	{
+		case BM_LOCK:
+		val = 'L';
+		break;
+		
+		case BM_KEEP:
+		val = 'K';
+		break;
+		
+		default:
+		val = 'O';
+		break;
+	}
+	MEM_Write8b(addr_bmode, val);
+}
+
+brakeMode_t Setings_GetBrakeMode(void)
+{
+	// Convert and return mode setting
+	uint8_t val = MEM_Read8b(addr_bmode);
+	switch(val)
+	{
+		case 'L':
+		return BM_LOCK;
+		
+		case 'K':
+		return BM_KEEP;
+		
+		default:
+		return BM_OPEN;
+	}
+}
+
+
+void Setings_SaveInputMode(inputMode_t inmode)
+{
+	// Convert and save input mode setting
+	uint8_t val = 0x00;
+	switch(inmode)
+	{
+		case IM_POT:
+		val = 'P';
+		break;
+		
+		default:
+		val = 'B';
+		break;
+	}
+	MEM_Write8b(addr_inmode, val);
+}
+
+inputMode_t Setings_GetInputMode(void)
+{
+	// Convert and return input mode setting
+	uint8_t val = MEM_Read8b(addr_inmode);
+	switch(val)
+	{
+		case 'P':
+		return IM_POT;
+		
+		default:
+		return IM_BUTTONS;
+	}
+}
+
+
+void Setings_SaveDisplayBrigthLvl(uint8_t value)
+{
+	MEM_Write8b(addr_dsp_bright, value);
+}
+
+uint8_t Setings_GetDisplayBrigthLvl(void)
+{
+	uint8_t val = MEM_Read8b(addr_dsp_bright);
+	if(val > 100) return 100;
+	else return val;
+}
+
+
+void Setings_SaveDisplayDimmLvl(uint8_t value)
+{
+	MEM_Write8b(addr_dsp_dimm, value);
+}
+
+uint8_t Setings_GetDisplayDimmLvl(void)
+{
+	uint8_t val = MEM_Read8b(addr_dsp_dimm);
+	if(val > 100) return 50;
+	else return val;
+}
+
+
+void Setings_SaveLockCurrent(uint16_t value)
+{
+	MEM_Write16b(addr_lock_amps, value);
+}
+
+uint16_t Setings_GetLockCurrent(void)
+{
+	uint16_t val = MEM_Read16b(addr_lock_amps);
+	if(val > 6000) return 4500;
+	else return val;
+}
+
+void Setings_SaveDefault(void)
+{
+	Setings_SaveForce(0);
+	Setings_SaveBrakeMode(BM_OPEN);
+	Setings_SaveInputMode(IM_BUTTONS);
+	Setings_SaveDisplayBrigthLvl(100);
+	Setings_SaveDisplayDimmLvl(50);
+	Setings_SaveLockCurrent(4500);
+}
+
+/**** Private function definitions ****/

firmware/logic/settings.h

@@ -0,0 +1,34 @@
+#ifndef SETTINGS_LOGIC_H_
+#define SETTINGS_LOGIC_H_
+
+/**** Includes ****/
+#include <stdint.h>
+#include "../devices/memory.h"
+#include "force.h"
+
+/**** Public definitions ****/
+
+/**** Public function declarations ****/
+void Setings_Update(uint8_t is_new_force, uint8_t force, uint8_t is_new_bmode, brakeMode_t bmode);
+
+void Setings_SaveForce(uint8_t value);
+uint8_t Setings_GetForce(void);
+
+void Setings_SaveBrakeMode(brakeMode_t bmode);
+brakeMode_t Setings_GetBrakeMode(void);
+
+void Setings_SaveInputMode(inputMode_t inmode);
+inputMode_t Setings_GetInputMode(void);
+
+void Setings_SaveDisplayBrigthLvl(uint8_t value);
+uint8_t Setings_GetDisplayBrigthLvl(void);
+
+void Setings_SaveDisplayDimmLvl(uint8_t value);
+uint8_t Setings_GetDisplayDimmLvl(void);
+
+void Setings_SaveLockCurrent(uint16_t value);
+uint16_t Setings_GetLockCurrent(void);
+
+void Setings_SaveDefault(void);
+
+#endif /* SETTINGS_LOGIC_H_ */

firmware/main.c

@@ -0,0 +1,170 @@
+/**** Includes ****/
+#include <stdint.h>
+
+#include "devices/config.h"
+#include "devices/analog.h"
+#include "devices/inputs.h"
+#include "devices/memory.h"
+
+#include "drivers/output.h"
+#include "drivers/display.h"
+
+#include "logic/force.h"
+#include "logic/coil.h"
+#include "logic/settings.h"
+
+/**** Private definitions ****/
+
+/**** Private constants ****/
+
+/**** Private variables ****/
+inputs_t inputs;
+analog_t analog;
+
+/**** Private function declarations ****/
+void Setup(void);
+void GatherData(uint8_t times);
+
+/**** Public function definitions ****/
+int main(void)
+{
+	Setup();
+	
+    while(1)
+    {
+		// Read all inputs
+		GatherData(1);
+		
+		// Process force logic
+		uint8_t force = Force_Update(&inputs, &analog);
+		
+		// Save values
+		uint8_t new_bmode = Force_IsNewBrakeMode();
+		uint8_t new_force = Force_IsNewUserForce();
+		if(Force_GetInputMode()==IM_POT) new_force = 0;
+		Setings_Update(new_force, force, new_bmode, Force_GetBrakeMode());
+		
+		// Set coil current target
+		Coil_SetTarget_Force(force);
+		
+		// Calculate next target voltage
+		uint16_t next_u = Coil_Update(&analog);
+		
+		// Set next output voltage
+		Output_SetTarget(next_u);
+		
+		// Update output
+		Output_Update(&analog);
+		
+		
+		// Display logic
+		if(Output_GetOutputState()==O_FAULTED)
+		{
+			// Show fault code
+			Display_SetLock(0);
+			Display_SetImage(0x33);
+		}
+		else if(Force_IsNewBrakeMode())
+		{
+			Display_SetLock(0);			
+			switch(Force_GetBrakeMode())
+			{
+				case BM_LOCK:
+				Display_SetImage(0x38);
+				break;
+				
+				case BM_KEEP:
+				Display_SetImage(0x1E);
+				break;
+				
+				default:
+				Display_SetImage(0x07);
+				break;
+			}
+			Display_SetLock(1000);
+		}
+		else
+		{
+			Display_SetPercent(force, DOT10);
+		}
+
+		// Update display
+		Display_Update(&inputs);
+		
+		// Reset new flags
+		Force_ResetNewBrakeMode();
+		Force_ResetNewUserForce();
+    }
+	
+	return 0;
+}
+
+/**** Private function definitions ****/
+void Setup(void)
+{
+	// Initialize low level hardware
+	Init_HW();
+	
+	// Prime EEPROM
+	//Setings_SaveDefault();
+	
+	// Configure inputs
+	Inputs_DefInit(&inputs);
+	
+	inputs.handbrake.cfg.act_level = HIGH;
+	inputs.handbrake.cfg.dbnc_treshold = 10;
+	
+	inputs.brakes.cfg.act_level = LOW;
+	inputs.brakes.cfg.dbnc_treshold = 20;
+	
+	inputs.dimm.cfg.act_level = LOW;
+	inputs.dimm.cfg.dbnc_treshold = 20;
+	
+	inputs.up.cfg.act_level = LOW;
+	inputs.up.cfg.dbnc_treshold = 20;
+	
+	inputs.down.cfg.act_level = LOW;
+	inputs.down.cfg.dbnc_treshold = 20;
+	
+	inputs.mode.cfg.act_level = LOW;
+	inputs.mode.cfg.dbnc_treshold = 20;
+	
+	Inputs_SetHanbrakePullUp(0);
+	
+	// Configure display
+	Display_CfgBacklight(100,50);
+	// Show startup display
+	Display_SetImage(0xFF);
+	Display_Update(&inputs);
+	
+	// Configure force logic
+	Force_CfgInputMode(IM_POT); //IM_BUTTONS IM_POT
+	
+	// Restore saved force
+	Force_SetUserForce(Setings_GetForce());
+	
+	// Restore saved brake mode
+	Force_SetBrakeMode(Setings_GetBrakeMode());
+
+	// Prime analog channels
+	GatherData(100);
+	
+	// Show default display
+	Display_SetImage(0x01);
+	Display_Update(&inputs);
+	
+	// Enable output
+	Output_Enable();
+	Output_SetTarget(0);
+}
+
+void GatherData(uint8_t times)
+{
+	do
+	{
+		Analog_UpdateAll(&analog);
+		Inputs_UpdateAll(&inputs);
+		if(times) times--;
+	}
+	while(times);
+}

firmware/uDCCD_Controller.atsln

@@ -0,0 +1,22 @@
+
+Microsoft Visual Studio Solution File, Format Version 12.00
+# Atmel Studio Solution File, Format Version 11.00
+VisualStudioVersion = 14.0.23107.0
+MinimumVisualStudioVersion = 10.0.40219.1
+Project("{54F91283-7BC4-4236-8FF9-10F437C3AD48}") = "uDCCD_Controller", "uDCCD_Controller.cproj", "{DCE6C7E3-EE26-4D79-826B-08594B9AD897}"
+EndProject
+Global
+	GlobalSection(SolutionConfigurationPlatforms) = preSolution
+		Debug|AVR = Debug|AVR
+		Release|AVR = Release|AVR
+	EndGlobalSection
+	GlobalSection(ProjectConfigurationPlatforms) = postSolution
+		{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Debug|AVR.ActiveCfg = Debug|AVR
+		{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Debug|AVR.Build.0 = Debug|AVR
+		{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Release|AVR.ActiveCfg = Release|AVR
+		{DCE6C7E3-EE26-4D79-826B-08594B9AD897}.Release|AVR.Build.0 = Release|AVR
+	EndGlobalSection
+	GlobalSection(SolutionProperties) = preSolution
+		HideSolutionNode = FALSE
+	EndGlobalSection
+EndGlobal

firmware/uDCCD_Controller.componentinfo.xml

@@ -0,0 +1,86 @@
+<?xml version="1.0" encoding="utf-8"?>
+<Store xmlns:i="http://www.w3.org/2001/XMLSchema-instance" xmlns="AtmelPackComponentManagement">
+	<ProjectComponents>
+		<ProjectComponent z:Id="i1" xmlns:z="http://schemas.microsoft.com/2003/10/Serialization/">
+			<CApiVersion></CApiVersion>
+			<CBundle></CBundle>
+			<CClass>Device</CClass>
+			<CGroup>Startup</CGroup>
+			<CSub></CSub>
+			<CVariant></CVariant>
+			<CVendor>Atmel</CVendor>
+			<CVersion>1.7.0</CVersion>
+			<DefaultRepoPath>C:/Program Files (x86)\Atmel\Studio\7.0\Packs</DefaultRepoPath>
+			<DependentComponents xmlns:d4p1="http://schemas.microsoft.com/2003/10/Serialization/Arrays" />
+			<Description></Description>
+			<Files xmlns:d4p1="http://schemas.microsoft.com/2003/10/Serialization/Arrays">
+				<d4p1:anyType i:type="FileInfo">
+					<AbsolutePath>C:/Program Files (x86)\Atmel\Studio\7.0\Packs\atmel\ATmega_DFP\1.7.374\include\</AbsolutePath>
+					<Attribute></Attribute>
+					<Category>include</Category>
+					<Condition>C</Condition>
+					<FileContentHash i:nil="true" />
+					<FileVersion></FileVersion>
+					<Name>include/</Name>
+					<SelectString></SelectString>
+					<SourcePath></SourcePath>
+				</d4p1:anyType>
+				<d4p1:anyType i:type="FileInfo">
+					<AbsolutePath>C:/Program Files (x86)\Atmel\Studio\7.0\Packs\atmel\ATmega_DFP\1.7.374\include\avr\iom328pb.h</AbsolutePath>
+					<Attribute></Attribute>
+					<Category>header</Category>
+					<Condition>C</Condition>
+					<FileContentHash>TU9y07FA4IWGxznrvGv9rQ==</FileContentHash>
+					<FileVersion></FileVersion>
+					<Name>include/avr/iom328pb.h</Name>
+					<SelectString></SelectString>
+					<SourcePath></SourcePath>
+				</d4p1:anyType>
+				<d4p1:anyType i:type="FileInfo">
+					<AbsolutePath>C:/Program Files (x86)\Atmel\Studio\7.0\Packs\atmel\ATmega_DFP\1.7.374\templates\main.c</AbsolutePath>
+					<Attribute>template</Attribute>
+					<Category>source</Category>
+					<Condition>C Exe</Condition>
+					<FileContentHash>YLr2MkKo6ZooP7MhARWYNA==</FileContentHash>
+					<FileVersion></FileVersion>
+					<Name>templates/main.c</Name>
+					<SelectString>Main file (.c)</SelectString>
+					<SourcePath></SourcePath>
+				</d4p1:anyType>
+				<d4p1:anyType i:type="FileInfo">
+					<AbsolutePath>C:/Program Files (x86)\Atmel\Studio\7.0\Packs\atmel\ATmega_DFP\1.7.374\templates\main.cpp</AbsolutePath>
+					<Attribute>template</Attribute>
+					<Category>source</Category>
+					<Condition>C Exe</Condition>
+					<FileContentHash>mkKaE95TOoATsuBGv6jmxg==</FileContentHash>
+					<FileVersion></FileVersion>
+					<Name>templates/main.cpp</Name>
+					<SelectString>Main file (.cpp)</SelectString>
+					<SourcePath></SourcePath>
+				</d4p1:anyType>
+				<d4p1:anyType i:type="FileInfo">
+					<AbsolutePath>C:/Program Files (x86)\Atmel\Studio\7.0\Packs\atmel\ATmega_DFP\1.7.374\gcc\dev\atmega328pb</AbsolutePath>
+					<Attribute></Attribute>
+					<Category>libraryPrefix</Category>
+					<Condition>GCC</Condition>
+					<FileContentHash i:nil="true" />
+					<FileVersion></FileVersion>
+					<Name>gcc/dev/atmega328pb</Name>
+					<SelectString></SelectString>
+					<SourcePath></SourcePath>
+				</d4p1:anyType>
+			</Files>
+			<PackName>ATmega_DFP</PackName>
+			<PackPath>C:/Program Files (x86)/Atmel/Studio/7.0/Packs/atmel/ATmega_DFP/1.7.374/Atmel.ATmega_DFP.pdsc</PackPath>
+			<PackVersion>1.7.374</PackVersion>
+			<PresentInProject>true</PresentInProject>
+			<ReferenceConditionId>ATmega328PB</ReferenceConditionId>
+			<RteComponents xmlns:d4p1="http://schemas.microsoft.com/2003/10/Serialization/Arrays">
+				<d4p1:string></d4p1:string>
+			</RteComponents>
+			<Status>Resolved</Status>
+			<VersionMode>Fixed</VersionMode>
+			<IsComponentInAtProject>true</IsComponentInAtProject>
+		</ProjectComponent>
+	</ProjectComponents>
+</Store>

firmware/uDCCD_Controller.cproj

@@ -0,0 +1,231 @@
+<?xml version="1.0" encoding="utf-8"?>
+<Project DefaultTargets="Build" xmlns="http://schemas.microsoft.com/developer/msbuild/2003" ToolsVersion="14.0">
+  <PropertyGroup>
+    <SchemaVersion>2.0</SchemaVersion>
+    <ProjectVersion>7.0</ProjectVersion>
+    <ToolchainName>com.Atmel.AVRGCC8.C</ToolchainName>
+    <ProjectGuid>dce6c7e3-ee26-4d79-826b-08594b9ad897</ProjectGuid>
+    <avrdevice>ATmega328PB</avrdevice>
+    <avrdeviceseries>none</avrdeviceseries>
+    <OutputType>Executable</OutputType>
+    <Language>C</Language>
+    <OutputFileName>$(MSBuildProjectName)</OutputFileName>
+    <OutputFileExtension>.elf</OutputFileExtension>
+    <OutputDirectory>$(MSBuildProjectDirectory)\$(Configuration)</OutputDirectory>
+    <AssemblyName>uDCCD_Controller</AssemblyName>
+    <Name>uDCCD_Controller</Name>
+    <RootNamespace>uDCCD_Controller</RootNamespace>
+    <ToolchainFlavour>Native</ToolchainFlavour>
+    <KeepTimersRunning>true</KeepTimersRunning>
+    <OverrideVtor>false</OverrideVtor>
+    <CacheFlash>true</CacheFlash>
+    <ProgFlashFromRam>true</ProgFlashFromRam>
+    <RamSnippetAddress>0x20000000</RamSnippetAddress>
+    <UncachedRange />
+    <preserveEEPROM>true</preserveEEPROM>
+    <OverrideVtorValue>exception_table</OverrideVtorValue>
+    <BootSegment>2</BootSegment>
+    <ResetRule>0</ResetRule>
+    <eraseonlaunchrule>0</eraseonlaunchrule>
+    <EraseKey />
+    <AsfFrameworkConfig>
+      <framework-data>
+        <options />
+        <configurations />
+        <files />
+        <documentation help="" />
+        <offline-documentation help="" />
+        <dependencies>
+          <content-extension eid="atmel.asf" uuidref="Atmel.ASF" version="3.42.0" />
+        </dependencies>
+      </framework-data>
+    </AsfFrameworkConfig>
+    <avrtool>com.atmel.avrdbg.tool.atmelice</avrtool>
+    <avrtoolserialnumber>J42700001490</avrtoolserialnumber>
+    <avrdeviceexpectedsignature>0x1E9516</avrdeviceexpectedsignature>
+    <com_atmel_avrdbg_tool_atmelice>
+      <ToolOptions>
+        <InterfaceProperties>
+          <IspClock>125000</IspClock>
+        </InterfaceProperties>
+        <InterfaceName>ISP</InterfaceName>
+      </ToolOptions>
+      <ToolType>com.atmel.avrdbg.tool.atmelice</ToolType>
+      <ToolNumber>J42700001490</ToolNumber>
+      <ToolName>Atmel-ICE</ToolName>
+    </com_atmel_avrdbg_tool_atmelice>
+    <avrtoolinterface>ISP</avrtoolinterface>
+    <avrtoolinterfaceclock>125000</avrtoolinterfaceclock>
+  </PropertyGroup>
+  <PropertyGroup Condition=" '$(Configuration)' == 'Release' ">
+    <ToolchainSettings>
+      <AvrGcc>
+        <avrgcc.common.Device>-mmcu=atmega328pb -B "%24(PackRepoDir)\atmel\ATmega_DFP\1.7.374\gcc\dev\atmega328pb"</avrgcc.common.Device>
+        <avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
+        <avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
+        <avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
+        <avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
+        <avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
+        <avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
+        <avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
+        <avrgcc.compiler.symbols.DefSymbols>
+          <ListValues>
+            <Value>NDEBUG</Value>
+          </ListValues>
+        </avrgcc.compiler.symbols.DefSymbols>
+        <avrgcc.compiler.directories.IncludePaths>
+          <ListValues>
+            <Value>%24(PackRepoDir)\atmel\ATmega_DFP\1.7.374\include\</Value>
+          </ListValues>
+        </avrgcc.compiler.directories.IncludePaths>
+        <avrgcc.compiler.optimization.level>Optimize for size (-Os)</avrgcc.compiler.optimization.level>
+        <avrgcc.compiler.optimization.PackStructureMembers>True</avrgcc.compiler.optimization.PackStructureMembers>
+        <avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
+        <avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
+        <avrgcc.linker.libraries.Libraries>
+          <ListValues>
+            <Value>libm</Value>
+          </ListValues>
+        </avrgcc.linker.libraries.Libraries>
+        <avrgcc.assembler.general.IncludePaths>
+          <ListValues>
+            <Value>%24(PackRepoDir)\atmel\ATmega_DFP\1.7.374\include\</Value>
+          </ListValues>
+        </avrgcc.assembler.general.IncludePaths>
+      </AvrGcc>
+    </ToolchainSettings>
+  </PropertyGroup>
+  <PropertyGroup Condition=" '$(Configuration)' == 'Debug' ">
+    <ToolchainSettings>
+      <AvrGcc>
+  <avrgcc.common.Device>-mmcu=atmega328pb -B "%24(PackRepoDir)\atmel\ATmega_DFP\1.7.374\gcc\dev\atmega328pb"</avrgcc.common.Device>
+  <avrgcc.common.outputfiles.hex>True</avrgcc.common.outputfiles.hex>
+  <avrgcc.common.outputfiles.lss>True</avrgcc.common.outputfiles.lss>
+  <avrgcc.common.outputfiles.eep>True</avrgcc.common.outputfiles.eep>
+  <avrgcc.common.outputfiles.srec>True</avrgcc.common.outputfiles.srec>
+  <avrgcc.common.outputfiles.usersignatures>False</avrgcc.common.outputfiles.usersignatures>
+  <avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>True</avrgcc.compiler.general.ChangeDefaultCharTypeUnsigned>
+  <avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>True</avrgcc.compiler.general.ChangeDefaultBitFieldUnsigned>
+  <avrgcc.compiler.symbols.DefSymbols>
+    <ListValues>
+      <Value>DEBUG</Value>
+    </ListValues>
+  </avrgcc.compiler.symbols.DefSymbols>
+  <avrgcc.compiler.directories.IncludePaths>
+    <ListValues>
+      <Value>%24(PackRepoDir)\atmel\ATmega_DFP\1.7.374\include\</Value>
+    </ListValues>
+  </avrgcc.compiler.directories.IncludePaths>
+  <avrgcc.compiler.optimization.PackStructureMembers>True</avrgcc.compiler.optimization.PackStructureMembers>
+  <avrgcc.compiler.optimization.AllocateBytesNeededForEnum>True</avrgcc.compiler.optimization.AllocateBytesNeededForEnum>
+  <avrgcc.compiler.optimization.DebugLevel>Default (-g2)</avrgcc.compiler.optimization.DebugLevel>
+  <avrgcc.compiler.warnings.AllWarnings>True</avrgcc.compiler.warnings.AllWarnings>
+  <avrgcc.linker.libraries.Libraries>
+    <ListValues>
+      <Value>libm</Value>
+    </ListValues>
+  </avrgcc.linker.libraries.Libraries>
+  <avrgcc.assembler.general.IncludePaths>
+    <ListValues>
+      <Value>%24(PackRepoDir)\atmel\ATmega_DFP\1.7.374\include\</Value>
+    </ListValues>
+  </avrgcc.assembler.general.IncludePaths>
+  <avrgcc.assembler.debugging.DebugLevel>Default (-Wa,-g)</avrgcc.assembler.debugging.DebugLevel>
+</AvrGcc>
+    </ToolchainSettings>
+  </PropertyGroup>
+  <ItemGroup>
+    <Compile Include="devices\analog.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\analog.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\common\level.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\config.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\config.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\led_display.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\led_display.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\filter_iir_lpf.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\filter_iir_lpf.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\halfbridge.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\halfbridge.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\hal\udccd_r7_hal.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\hal\udccd_hal.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\inputs.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\inputs.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\memory.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="devices\memory.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="drivers\display.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="drivers\display.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="drivers\output.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="drivers\output.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="logic\coil.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="logic\coil.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="logic\force.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="logic\force.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="logic\settings.c">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="logic\settings.h">
+      <SubType>compile</SubType>
+    </Compile>
+    <Compile Include="main.c">
+      <SubType>compile</SubType>
+    </Compile>
+  </ItemGroup>
+  <ItemGroup>
+    <Folder Include="devices" />
+    <Folder Include="devices\hal" />
+    <Folder Include="devices\common" />
+    <Folder Include="drivers" />
+    <Folder Include="logic" />
+  </ItemGroup>
+  <Import Project="$(AVRSTUDIO_EXE_PATH)\\Vs\\Compiler.targets" />
+</Project>

pcb/main board/settings/Private_OutJob_v2.OutJob

@@ -287,7 +287,7 @@ OutputEnabled10_OutputMedium10=0
 OutputDefault10=0
 PageOptions10=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.00|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 Configuration10_Name1=OutputConfigurationParameter1
-Configuration10_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=29981830|ViewY=21653544|LookAtX=132874016|LookAtY=128937008|LookAtZ=0|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=0|QuatZ=0|QuatW=1|Zoom=5.88356367120992E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=True|ScreenWidth=1764|ScreenHeight=1274|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3FALSE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3FALSE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\315238730\2CFG3D.WORKSPACEENDCOLOR\315238730\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=Z:\MicroRally\Electronics\uDCCD_Controller\Main board\Source\uDCCD_Controller.PcbDoc
+Configuration10_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=29527560|ViewY=22794078|LookAtX=132874016|LookAtY=128937008|LookAtZ=0|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=0|QuatZ=0|QuatW=1|Zoom=4.00981332033562E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=True|ScreenWidth=1184|ScreenHeight=914|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3FALSE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3FALSE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\315238730\2CFG3D.WORKSPACEENDCOLOR\315238730\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=D:\Microrally\uDCCD_Controller_HW\Main board\Source\uDCCD_Controller.PcbDoc
 OutputType11=PCB 3D Print
 OutputName11=BotTexture
 OutputCategory11=Documentation
@@ -307,7 +307,7 @@ OutputEnabled11_OutputMedium10=0
 OutputDefault11=0
 PageOptions11=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.00|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 Configuration11_Name1=OutputConfigurationParameter1
-Configuration11_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=29981830|ViewY=21653544|LookAtX=132874016|LookAtY=128937008|LookAtZ=0|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=1|QuatZ=0|QuatW=0|Zoom=5.88356367120992E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1764|ScreenHeight=1274|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3FALSE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3FALSE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\315238730\2CFG3D.WORKSPACEENDCOLOR\315238730\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=Z:\MicroRally\Electronics\uDCCD_Controller\Main board\Source\uDCCD_Controller.PcbDoc
+Configuration11_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=29527560|ViewY=22794078|LookAtX=132874016|LookAtY=128937008|LookAtZ=0|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=1|QuatZ=0|QuatW=0|Zoom=4.00981332033562E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1184|ScreenHeight=914|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3FALSE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3FALSE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\315238730\2CFG3D.WORKSPACEENDCOLOR\315238730\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=D:\Microrally\uDCCD_Controller_HW\Main board\Source\uDCCD_Controller.PcbDoc
 OutputType12=PCB 3D Print
 OutputName12=PCB Picture Top
 OutputCategory12=Documentation
@@ -325,9 +325,9 @@ OutputEnabled12_OutputMedium8=0
 OutputEnabled12_OutputMedium9=0
 OutputEnabled12_OutputMedium10=0
 OutputDefault12=0
-PageOptions12=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.99|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
+PageOptions12=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=2.32|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 Configuration12_Name1=OutputConfigurationParameter1
-Configuration12_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=46249296|ViewY=33402268|LookAtX=133598160|LookAtY=124806528|LookAtZ=-18408|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=0|QuatZ=0|QuatW=1|Zoom=3.81411216523329E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=True|ScreenWidth=1764|ScreenHeight=1274|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=Z:\MicroRally\Electronics\uDCCD_Controller\Main board\Source\uDCCD_Controller.PcbDoc
+Configuration12_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=46114880|ViewY=35598816|LookAtX=133146664|LookAtY=125013736|LookAtZ=-18408|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=0|QuatZ=0|QuatW=1|Zoom=2.56750105372724E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=True|ScreenWidth=1184|ScreenHeight=914|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=D:\Microrally\uDCCD_Controller_HW\Main board\Source\uDCCD_Controller.PcbDoc
 OutputType13=PCB 3D Print
 OutputName13=PCB Picture Bot
 OutputCategory13=Documentation
@@ -345,9 +345,9 @@ OutputEnabled13_OutputMedium8=0
 OutputEnabled13_OutputMedium9=0
 OutputEnabled13_OutputMedium10=0
 OutputDefault13=0
-PageOptions13=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.99|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
+PageOptions13=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=2.32|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 Configuration13_Name1=OutputConfigurationParameter1
-Configuration13_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=46249296|ViewY=33402268|LookAtX=133598160|LookAtY=124806528|LookAtZ=18408|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=1|QuatZ=0|QuatW=0|Zoom=3.81411216523329E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1764|ScreenHeight=1274|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=Z:\MicroRally\Electronics\uDCCD_Controller\Main board\Source\uDCCD_Controller.PcbDoc
+Configuration13_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=46114880|ViewY=35598816|LookAtX=132601368|LookAtY=125013736|LookAtZ=646303|UpX=0|UpY=1|UpZ=0|FOV=45|QuatX=0|QuatY=1|QuatZ=0|QuatW=0|Zoom=2.56750105372724E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1184|ScreenHeight=914|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32147483647\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=D:\Microrally\uDCCD_Controller_HW\Main board\Source\uDCCD_Controller.PcbDoc
 OutputType14=PCB 3D Print
 OutputName14=PCB Picture 1
 OutputCategory14=Documentation
@@ -365,9 +365,9 @@ OutputEnabled14_OutputMedium8=0
 OutputEnabled14_OutputMedium9=0
 OutputEnabled14_OutputMedium10=0
 OutputDefault14=0
-PageOptions14=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.62|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
+PageOptions14=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.75|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 Configuration14_Name1=OutputConfigurationParameter1
-Configuration14_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=69744264|ViewY=50370856|LookAtX=133328896|LookAtY=127375536|LookAtZ=-18406.26171875|UpX=-0.420631378889084|UpY=-0.648587167263031|UpZ=-0.634353160858154|FOV=45|QuatX=-0.0764413699507713|QuatY=-0.328605562448502|QuatZ=0.904682457447052|QuatW=0.260240256786346|Zoom=3.12942035292045E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1764|ScreenHeight=1274|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32000\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=Z:\MicroRally\Electronics\uDCCD_Controller\Main board\Source\uDCCD_Controller.PcbDoc
+Configuration14_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=61261620|ViewY=47291488|LookAtX=133454520|LookAtY=126706752|LookAtZ=-18405.337890625|UpX=-0.420631378889084|UpY=-0.648587167263031|UpZ=-0.634353160858154|FOV=45|QuatX=-0.0764409825205803|QuatY=-0.328605175018311|QuatZ=0.904682576656342|QuatW=0.260240107774734|Zoom=1.93269459719063E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1184|ScreenHeight=914|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32000\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=D:\Microrally\uDCCD_Controller_HW\Main board\Source\uDCCD_Controller.PcbDoc
 OutputType15=PCB 3D Print
 OutputName15=PCB Picture 2
 OutputCategory15=Documentation
@@ -385,9 +385,9 @@ OutputEnabled15_OutputMedium8=0
 OutputEnabled15_OutputMedium9=0
 OutputEnabled15_OutputMedium10=0
 OutputDefault15=0
-PageOptions15=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.66|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
+PageOptions15=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.92|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 Configuration15_Name1=OutputConfigurationParameter1
-Configuration15_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=56316332|ViewY=40672908|LookAtX=130628320|LookAtY=123914320|LookAtZ=-18406.16796875|UpX=0.50720202922821|UpY=0.461718440055847|UpZ=-0.727710068225861|FOV=45|QuatX=-0.368430107831955|QuatY=0.146614283323288|QuatZ=-0.365239500999451|QuatW=0.842237234115601|Zoom=3.27886040318443E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1764|ScreenHeight=1274|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32000\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=Z:\MicroRally\Electronics\uDCCD_Controller\Main board\Source\uDCCD_Controller.PcbDoc
+Configuration15_Item1=Record=Pcb3DPrintView|ResX=600|ResY=600|ViewX=55774212|ViewY=43055432|LookAtX=130913112|LookAtY=123099560|LookAtZ=-18406.123046875|UpX=0.50720202922821|UpY=0.461718440055847|UpZ=-0.727710068225861|FOV=45|QuatX=-0.368430495262146|QuatY=0.146614402532578|QuatZ=-0.365239381790161|QuatW=0.842237174510956|Zoom=2.12284489663411E-5|UnitsPercent=True|UnitsDPI=True|LockResAspect=True|ViewConfigType=.config_3d|CustomCamera=True|ViewFromTop=False|ScreenWidth=1184|ScreenHeight=914|ImageOutputType=1|ViewConfig=RECORD\3Board\2CFGALL.CONFIGURATIONKIND\33\2CFGALL.CONFIGURATIONDESC\3Enter%20description%20of%20new%20view%20configuration\2CFGALL.COMPONENTBODYREFPOINTCOLOR\316777215\2CFGALL.COMPONENTBODYSNAPPOINTCOLOR\316777215\2CFGALL.SHOWCOMPONENTSNAPMARKERS\3FALSE\2CFGALL.SHOWCOMPONENTSNAPREFERENCE\3FALSE\2CFGALL.SHOWCOMPONENTSNAPCUSTOM\3FALSE\2CFG3D.POSITIVETOPSOLDERMASK\3TRUE\2CFG3D.POSITIVEBOTTOMSOLDERMASK\3TRUE\2CFG3D.SHOWCOMPONENTBODIES\3TRUE\2CFG3D.SHOWCOMPONENTSTEPMODELS\3TRUE\2CFG3D.COMPONENTMODELPREFERENCE\30\2CFG3D.SHOWCOMPONENTAXES\3TRUE\2CFG3D.SHOWBOARDCORE\3TRUE\2CFG3D.SHOWBOARDPREPREG\3TRUE\2CFG3D.SHOWTOPSILKSCREEN\3TRUE\2CFG3D.SHOWBOTSILKSCREEN\3TRUE\2CFG3D.SHOWORIGINMARKER\3TRUE\2CFG3D.EYEDIST\32000\2CFG3D.SHOWCUTOUTS\3TRUE\2CFG3D.SHOWROUTETOOLPATH\3TRUE\2CFG3D.SHOWROOMS3D\3FALSE\2CFG3D.USESYSCOLORSFOR3D\3FALSE\2CFG3D.WORKSPACECOLOR\316777215\2CFG3D.BOARDCORECOLOR\34216160\2CFG3D.BOARDPREPREGCOLOR\30\2CFG3D.TOPSOLDERMASKCOLOR\35994299\2CFG3D.BOTSOLDERMASKCOLOR\35994299\2CFG3D.COPPERCOLOR\38315135\2CFG3D.TOPSILKSCREENCOLOR\316777215\2CFG3D.BOTSILKSCREENCOLOR\316777215\2CFG3D.WORKSPACELUMINANCEVARIATION\330\2CFG3D.WORKSPACEBEGINCOLOR\316777215\2CFG3D.WORKSPACEENDCOLOR\315724527\2CFG3D.WORKSPACECOLOROPACITY\31.000000\2CFG3D.BOARDCORECOLOROPACITY\30.900000\2CFG3D.BOARDPREPREGCOLOROPACITY\30.500000\2CFG3D.TOPSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.BOTSOLDERMASKCOLOROPACITY\30.900000\2CFG3D.COPPERCOLOROPACITY\31.000000\2CFG3D.TOPSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOTSILKSCREENCOLOROPACITY\31.000000\2CFG3D.BOARDTHICKNESSSCALING\31.000000\2CFG3D.SHOWMECHANICALLAYERS\3FALSE\2CFG3D.MECHANICALLAYERSOPACITY\31.000000\2CFG3D.MECHCOVERLAYERUPDATED\3FALSE|DocumentPath=D:\Microrally\uDCCD_Controller_HW\Main board\Source\uDCCD_Controller.PcbDoc
 OutputType16=Composite
 OutputName16=Gerber Notes
 OutputCategory16=Documentation
@@ -617,20 +617,20 @@ ShowComponentParameters3=0
 GlobalBookmarks3=0
 PDFACompliance3=Disabled
 PDFVersion3=Default
-OutputFilePath4=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+OutputFilePath4=D:\Microrally\uDCCD_Controller_HW\Main board\OUTPUTS\uDCCD_Controller\
 ReleaseManaged4=0
 OutputBasePath4=OUTPUTS\
 OutputPathMedia4==UT_Output_file_name
 OutputPathMediaValue4==UT_Output_file_name
 OutputPathOutputer4=[Output Custom]
 OutputPathOutputerPrefix4=
-OutputPathOutputerValue4=3D_MODEL
+OutputPathOutputerValue4==UT_Output_file_name+'_'+UT_PCB_Revision+'_3D_MODEL'
 OutputFileName4=
 OutputFileNameMulti4==UT_Output_file_name+'_'+UT_PCB_Revision+'_'+OutputName
 UseOutputNameForMulti4=0
 OutputFileNameSpecial4=
 OpenOutput4=0
-OutputFilePath5=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+OutputFilePath5=D:\Microrally\uDCCD_Controller_HW\Main board\OUTPUTS\uDCCD_Controller\
 ReleaseManaged5=0
 OutputBasePath5=OUTPUTS\
 OutputPathMedia5==UT_Output_file_name
@@ -643,7 +643,7 @@ OutputFileNameMulti5==UT_Output_file_name+'_'+UT_PCB_Revision
 UseOutputNameForMulti5=0
 OutputFileNameSpecial5=
 OpenOutput5=0
-OutputFilePath6=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+OutputFilePath6=F:\MicroRally\uDCCD Controller\Electronics\Main board\OUTPUTS\uDCCD_Controller\
 ReleaseManaged6=0
 OutputBasePath6=OUTPUTS\
 OutputPathMedia6==UT_Output_file_name
@@ -683,7 +683,7 @@ ShowComponentParameters7=0
 GlobalBookmarks7=0
 PDFACompliance7=Disabled
 PDFVersion7=Default
-OutputFilePath8=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+OutputFilePath8=F:\MicroRally\uDCCD Controller\Electronics\Main board\OUTPUTS\uDCCD_Controller\
 ReleaseManaged8=0
 OutputBasePath8=OUTPUTS\
 OutputPathMedia8==UT_Output_file_name
@@ -696,14 +696,14 @@ OutputFileNameMulti8==UT_Output_file_name+'_'+UT_PCB_Revision+UT_BOM_Version+'_B
 UseOutputNameForMulti8=0
 OutputFileNameSpecial8=
 OpenOutput8=0
-OutputFilePath9=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+OutputFilePath9=D:\Microrally\uDCCD_Controller_HW\Main board\OUTPUTS\uDCCD_Controller\
 ReleaseManaged9=0
 OutputBasePath9=OUTPUTS\
 OutputPathMedia9==UT_Output_file_name
 OutputPathMediaValue9==UT_Output_file_name
-OutputPathOutputer9=3D_MODEL
+OutputPathOutputer9=[Output Custom]
 OutputPathOutputerPrefix9=3D_MODEL
-OutputPathOutputerValue9==UT_Output_file_name+'_'+UT_PCB_Revision+UT_BOM_Version+'_MODEL'
+OutputPathOutputerValue9==UT_Output_file_name+'_'+UT_PCB_Revision+'_3D_MODEL'
 OutputFileName9=
 OutputFileNameMulti9==UT_Output_file_name+'_'+UT_PCB_Revision+UT_BOM_Version+'_MODEL'
 UseOutputNameForMulti9=0
@@ -728,7 +728,7 @@ RelativeOutputPath2=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\R1V1\DataTrack
 OpenOutputs2=0
 RelativeOutputPath3=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker_R1_PCB.PDF
 OpenOutputs3=0
-RelativeOutputPath4=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+RelativeOutputPath4=D:\Microrally\uDCCD_Controller_HW\Main board\OUTPUTS\uDCCD_Controller\
 OpenOutputs4=0
 AddToProject4=0
 TimestampFolder4=0
@@ -738,7 +738,7 @@ OpenGerberOutput4=0
 OpenNCDrillOutput4=0
 OpenIPCOutput4=0
 EnableReload4=0
-RelativeOutputPath5=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+RelativeOutputPath5=D:\Microrally\uDCCD_Controller_HW\Main board\OUTPUTS\uDCCD_Controller\
 OpenOutputs5=0
 AddToProject5=0
 TimestampFolder5=0
@@ -748,7 +748,7 @@ OpenGerberOutput5=0
 OpenNCDrillOutput5=0
 OpenIPCOutput5=0
 EnableReload5=0
-RelativeOutputPath6=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+RelativeOutputPath6=F:\MicroRally\uDCCD Controller\Electronics\Main board\OUTPUTS\uDCCD_Controller\
 OpenOutputs6=0
 AddToProject6=0
 TimestampFolder6=0
@@ -760,7 +760,7 @@ OpenIPCOutput6=0
 EnableReload6=0
 RelativeOutputPath7=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker_R1V1_PIC.PDF
 OpenOutputs7=0
-RelativeOutputPath8=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+RelativeOutputPath8=F:\MicroRally\uDCCD Controller\Electronics\Main board\OUTPUTS\uDCCD_Controller\
 OpenOutputs8=0
 AddToProject8=0
 TimestampFolder8=0
@@ -770,7 +770,7 @@ OpenGerberOutput8=0
 OpenNCDrillOutput8=0
 OpenIPCOutput8=0
 EnableReload8=0
-RelativeOutputPath9=Z:\MicroRally\Electronics\DataTracker\OUTPUTS\DataTracker\
+RelativeOutputPath9=D:\Microrally\uDCCD_Controller_HW\Main board\OUTPUTS\uDCCD_Controller\
 OpenOutputs9=0
 AddToProject9=0
 TimestampFolder9=0

pcb/main board/uDCCD_Controller.PrjPcb

@@ -305,24 +305,24 @@ DocumentPath=Project Outputs for uDCCD_Controller\Design Rule Check - uDCCD_Cont
 DItemRevisionGUID=
 
 [Parameter1]
-Name=UT_BOM_Version
+Name=UT_Project_Name
-Value=V1
+Value=uDCCD Controller
 
 [Parameter2]
-Name=UT_Output_file_name
+Name=UT_PCB_Revision
-Value=uDCCD Controller
+Value=R9
 
 [Parameter3]
 Name=UT_PCB_Designer
 Value=Andis Zīle
 
 [Parameter4]
-Name=UT_PCB_Revision
+Name=UT_Output_file_name
-Value=R8
+Value=uDCCD_Controller
 
 [Parameter5]
-Name=UT_Project_Name
+Name=UT_BOM_Version
-Value=uDCCD Controller
+Value=V1
 
 [Configuration1]
 Name=Sources
@@ -544,6 +544,12 @@ OutputDocumentPath13=
 OutputVariantName13=[No Variations]
 OutputDefault13=0
 PageOptions13=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.00|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
+OutputType14=PCBDrawing
+OutputName14=Draftsman
+OutputDocumentPath14=
+OutputVariantName14=[No Variations]
+OutputDefault14=0
+PageOptions14=Record=PageOptions|CenterHorizontal=True|CenterVertical=True|PrintScale=1.00|XCorrection=1.00|YCorrection=1.00|PrintKind=1|BorderSize=5000000|LeftOffset=0|BottomOffset=0|Orientation=2|PaperLength=1000|PaperWidth=1000|Scale=100|PaperSource=7|PrintQuality=-3|MediaType=1|DitherType=10|PrintScaleMode=1|PaperKind=A4|PaperIndex=9
 
 [OutputGroup4]
 Name=Assembly Outputs